Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

CAP1552E with CT5508

      i have 12 nos CAP3602I, 4 nos of CAP1552E and CT5508 , i have added all the indoor caps (3602I) in controller, but outdoor caps (1552E) are not adding, so anyone please help me.

thanks

Debu     

34 REPLIES
Hall of Fame Super Silver

Re: CAP1552E with CT5508

For MESH AP's you need to add the Ethernet MAC address to the Mac filter on the WLC. This is a requirement.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

CAP1552E with CT5508

i have done, but its not showing in ap list, another thing is that when i will try to configure the caps through console its configured and ssid's also broadcasting, and its working like standalone ap.

thanks

debu

Hall of Fame Super Silver

Re: CAP1552E with CT5508

Please refer to this guide, adding the Mac filter.

http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.4/design/guide/mesh74_chapter_0101.html#ID4807

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: CAP1552E with CT5508

Here is a link specific to the 1552 which you have, but they are all the same. The mesh will not join unless you add the Mesh AP's MAC address to the WLC.

http://www.cisco.com/en/US/docs/wireless/access_point/1550/quick/guide/ap1550qsg.html#wp45556

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
VIP Purple

Re: CAP1552E with CT5508

HI Debu,

Can you paste the output of these commands:

From WLC: sh sysinfo

From AP: sh vrsion

Also console to AP and paste the entire bootproess here.

For mesh AP: Dont forget to add MAC address in mac filter list.

Security > AAA > Mac Filter then add the mac of AP here.

Reagrds

Dont forget to rate helpful posts.

New Member

Re: CAP1552E with CT5508

se the following details

from WLC

show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.4.121.0

Bootloader Version............................... 1.0.18

Field Recovery Image Version..................... 7.6.95.16

Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2

Build Type....................................... DATA + WPS

System Name...................................... Cisco_db:47:84

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

Redundancy Mode.................................. Disabled

IP Address....................................... 10.10.3.2

Last Reset....................................... Power on reset

System Up Time................................... 0 days 0 hrs 17 mins 32 secs

System Timezone Location.........................

System Stats Realtime Interval................... 5

System Stats Normal Interval..................... 180

Configured Country............................... IN  - India

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +36 C

External Temperature............................. +23 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

Number of Active Clients......................... 0

Memory Current Usage............................. Unknown

Memory Average Usage............................. Unknown

CPU Current Usage................................ Unknown

CPU Average Usage................................ Unknown

Burned-in MAC Address............................ 78:DA:6E:DB:47:80

Power Supply 1................................... Present, Power Off, Fan On

Power Supply 2................................... Present, OK

Maximum number of APs supported.................. 25

(Cisco Controller) >

from AP

sho version

Cisco IOS Software, C1550 Software (C1520-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Tue 11-Dec-12 05:12 by prod_rel_team

ROM: Bootstrap program is C1550 boot loader

BOOTLDR: C1550 Boot Loader (C1520-BOOT-M) LoaderVersion 15.2(2a)JA, RELEASE SOFTWARE (fc1)

ap uptime is 7 minutes

System returned to ROM by power source change

System image file is "flash:/c1520-k9w7-mx.152-2.JB/c1520-k9w7-xx.152-2.JB"

Last reload reason:

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

--More--                           agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-SAP1552E-N-K9    (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.

Processor board ID FTX1802P1HT

PowerPC 8349 CPU at 533Mhz, revision number 0x0031

Last reset from power source change

AVR Microcontroller 1 - SW Version: 00.01.02

AVR Microcontroller 2 - SW Version: 00.01.09

AVR Microcontroller 6 - SW Version: 00.01.00

4 Gigabit Ethernet interfaces

2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 7C:95:F3:8A:26:E0

Part Number                          : 73-13538-02

--More--                           PCA Assembly Number                  : 800-31224-01

PCA Revision Number                  : 03

PCB Serial Number                    : FOC17207LNQ

Top Assembly Part Number             : 800-34851-05

Top Assembly Serial Number           : FTX1802P1HT

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP1552E-N-K9  

Configuration register is 0xF

ap#

thanks

Debu

VIP Purple

Re: CAP1552E with CT5508

HI Debu,

Debudas123 wrote:


ap uptime is 7 minutes

System returned to ROM by power source change

System image file is "flash:/c1520-k9w7-mx.152-2.JB/c1520-k9w7-xx.152-2.JB"

Last reload reason:

As per your post , you have autonomous image on WLC and you need lighweight image to connect to a WLC:

Following are the three type of IOS available & need to download the correct type before starting the conversion process.

  • k9w7 – autonomous IOS
  • k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on “mesh” APs)
  • rcvk9w8 –  lightweight recovery image – this is factory installed on lightweight  APs, unless a “mesh” image is specified; it lacks radio firmware

For the LWAP conversion, use the recovery image ( e.g  c1140-rcvk9w8-tar.124-25d.JAL.tar). We can use the same command on the autonomous AP priviledge mode.

AP5475.d0f5.2ee7#archive download-sw /force-reload /overwrite tftp://IP/xyz-rcvk9w8-tar.......tar

check this link for help:

http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

Regards

Dont forget to rate helpful posts

Hall of Fame Super Silver

Re: CAP1552E with CT5508

You have an autonomous AP

Cisco IOS Software, C1550 Software (C1520-K9W7-M)

You need to download a lightweight image.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: CAP1552E with CT5508

You can download the software here.

c1520-k9w8-tar.152-4.JB3.tar

http://software.cisco.com/download/release.html?mdfid=283791419&flowid=24862&softwareid=280775090&release=15.2.4-JB3&relind=AVAILABLE&rellifecycle=ED&reltype=latest

K9w7 is autonomous
K9w8 is lightweight

Ways to convert autonomous to lightweight and vice versa. Might be east for you to do the archive download command.

Using a TFTP Server to Return to a Previous Release

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

https://supportforums.cisco.com/docs/DOC-18268

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

http://www.youtube.com/watch?v=QQ_NuxdRhQ4

https://supportforums.cisco.com/docs/DOC-14960

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: CAP1552E with CT5508

Archive download.... Support doc

https://supportforums.cisco.com/docs/DOC-14960

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

Re: CAP1552E with CT5508

Hi,

after upgrading the firmware, one cap's connected okay, but rest of three showing the error, i hav ementioned following

AP189c.5d8f.e080#
*Feb 11 12:15:42.099: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 12:16:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.10.3.2 peer_port: 5246
*Feb 11 12:16:34.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_
dtls_connection_db.c:2051 Max retransmission count reached!
*Feb 11 12:17:04.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
10.3.2:5246
*Feb 11 12:17:04.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 12:16:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.10.3.2 peer_port: 5246
*Feb 11 12:16:24.899: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Feb 11 12:16:24.899: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Feb 11 12:16:24.899: %MESH-6-LINK_UPDOWN: Mesh station 189c.5d8f.e09c link Down

*Feb 11 12:16:34.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_
dtls_connection_db.c:2051 Max retransmission count reached!

what i will do ..

thanks

Debu

VIP Purple

Re: CAP1552E with CT5508

HI debu,

Add the MAC address of the MAP to the MAC filter table. In order to do this, choose

securiyt > AAA > Mac Filtering > Mac Address

Reagrds

New Member

CAP1552E with CT5508

already added

thanks

Debu

VIP Purple

CAP1552E with CT5508

HI Debu,

Something is blocking.....

because AP is getting IP and you can ping the WLC. AP fails to join means that UDP 5246 and or UDP 5247 is being blocked.

If still fails then factory reset the AP with mode buuton

Resetting to Default Settings Using the MODE Button

#

Follow these steps to reset the access point to factory default settings using the access point MODE button:


Step 1Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point

Step 2 Press and hold the MODE button while you reconnect power to the access point.

Step 3 Hold  the MODE button until the Status LED turns amber (approximately 1 to 2  seconds), and release the button. All access point settings return to  factory defaults.

follow this posts:

http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/

If still faile then paste the full logs from console of AP.

Reagrds

New Member

CAP1552E with CT5508

where is the mode botton? only one reset botton is there...

thanks

debu

VIP Purple

CAP1552E with CT5508

do it via Reset button.

Reagrds

New Member

CAP1552E with CT5508

nothing happens..

thanks

Debu

VIP Purple

Re: CAP1552E with CT5508

First check if the is checked?   security > AP Policy ---> Accept Manufactured Installed  Certificate (MIC)

1.  paste the log again ?

2. SH VERSION  and the logs from console.

3.Also paste the screenshot of this page: security > AP Policy

Regards

New Member

CAP1552E with CT5508

log

*Feb 11 14:48:40.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_
dtls_connection_db.c:2051 Max retransmission count reached!
*Feb 11 14:48:45.099: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Feb 11 14:48:45.099: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Feb 11 14:48:45.099: %MESH-6-LINK_UPDOWN: Mesh station 189c.5d8f.e09c link Down

*Feb 11 14:49:10.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
10.3.2:5246
*Feb 11 14:49:10.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 14:48:11.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.10.3.2 peer_port: 5246
% CDP is not supported on this interface, or for this encapsulation
*Feb 11 14:48:25.483: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
10.3.2:5246
*Feb 11 14:48:25.483: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Feb 11 14:48:25.583: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallbac
k to DHCP.

*Feb 11 14:48:37.587: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 14:49:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.10.3.2 peer_port: 5246

version

Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.2(2)JB3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 19-Dec-13 04:59 by prod_rel_team

Initializing flashfs...

Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.2(2)JB3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 19-Dec-13 04:59 by prod_rel_team

ROM: Bootstrap program is C1550 boot loader
BOOTLDR: C1550 Boot Loader (C1520-BOOT-M) LoaderVersion 15.2(2a)JA, RELEASE SOFTWARE (fc1)

AP189c.5d8f.e080 uptime is 14 minutes
System returned to ROM by power source change
System image file is "flash:/c1520-k9w8-mx.152-2.JB3/c1520-k9w8-xx.152-2.JB3"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
--More--                           agree to comply with applicable laws and regulations. If you are unable
--More--                           to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP1552E-N-K9    (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1802P1HW
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power source change
LWAPP image version 7.4.121.0
AVR Microcontroller 1 - SW Version: 00.01.02
AVR Microcontroller 2 - SW Version: 00.01.09
AVR Microcontroller 6 - SW Version: 00.01.00
4 Gigabit Ethernet interfaces
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 18:9C:5D:8F:E0:80
Part Number                          : 73-13538-02
--More--                           PCA Assembly Number                  : 800-31224-01
PCA Revision Number                  : 03
PCB Serial Number                    : FOC17506W6T
Top Assembly Part Number             : 800-34851-05
Top Assembly Serial Number           : FTX1802P1HW
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP1552E-N-K9  

Configuration register is 0xF

AP189c.5d8f.e080#

wlc.jpg

New Member

CAP1552E with CT5508

okay

now its working...

but when i have configure 1 RAP and 1 MAP both are not connecting into mess network, what will be the issue ?

thanks

Debu

VIP Purple

CAP1552E with CT5508

Glad that worked...

Here is the guide for mesh deployment:

http://www.cisco.com/c/en/us/support/docs/wireless/aironet-1522-lightweight-outdoor-mesh-access-point/113678-wlan-mesh-config-ex.html

Reagrds

Dont forget to rate helpful posts and mak this question as answered, it may help others.

New Member

CAP1552E with CT5508

Thanks

but now some error is showing in MAP's console

e from controller

*Feb 11 17:56:48.919: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

e from controller

*Feb 11 17:56:48.919: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:10.807: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:25.539: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 11 17:57:48.919: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

VIP Purple

CAP1552E with CT5508

is this connected to controller ???

did you changed the role for an access point from WLC ??

http://www.cisco.com/c/en/us/support/docs/wireless/aironet-1522-lightweight-outdoor-mesh-access-point/113678-wlan-mesh-config-ex.html

Regards

dont forget to rate helpful posts

New Member

CAP1552E with CT5508

Hi,

  this ap is not connected with controller, it is connected with root ap.

yes i have change the role of the ap from controller.

Thanks

Debu

New Member

Re: CAP1552E with CT5508

Hi,

another issue is there users are unable to connect the wi-fi, ssid's are showing, but unable to connect, and still showing the following error

e from controller

*Feb 12 10:06:44.595: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

e from controller

*Feb 12 10:06:44.595: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr

ol Message from 10.10.3.2

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 34078720.

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag

e from controller

*Feb 12 10:06:55.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p

acket from 10.10.3.2

Hall of Fame Super Silver

Re: CAP1552E with CT5508

Debu,

Did you add the MAC address of both mesh APs to the Mac filter list? Did you have bother connected on the network wired so that they can join the WLC and download the code? Do you have AC power adapter, correct power injector or the right power source to power up these AP's, if not, the radios will not come up. Also make sure you have the antennas connected. Do you also have any other AP's joined to this WLC?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
New Member

CAP1552E with CT5508

Hi,

  everything is okay, but still showing the error.

Thanks

Debu

Hall of Fame Super Silver

CAP1552E with CT5508

Everything is working fine, its just the error that your concerned with?

Thanks,

Scott

*****Help out other by using the rating system and marking answered questions as "Answered"*****

-Scott
*** Please rate helpful posts ***
New Member

CAP1552E with CT5508

yes..

thanks

961
Views
0
Helpful
34
Replies
CreatePlease to create content