Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Change IOS on 1131AG AP from Lightweight to Autonomous

hi experts,

can someone advice if the 1131ag ap's IOS can be changed to autonomous? can you give me a link where i could get an autonomous IOS and how to do it? thanks!

2 ACCEPTED SOLUTIONS

Accepted Solutions
Hall of Fame Super Gold

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:

Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.

Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.

Step 3 Set the timeout value on the TFTP server to 30 seconds.

Step 4 On the PC where the TFTP server is located, perform these steps:

a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.

b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.

Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.

Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.

Step 7 Disconnect power from the access point.

Step 8 Press and hold MODE while you reconnect power to the access point.

Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.

Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

Correct

6 REPLIES
Hall of Fame Super Gold

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:

Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.

Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.

Step 3 Set the timeout value on the TFTP server to 30 seconds.

Step 4 On the PC where the TFTP server is located, perform these steps:

a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.

b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.

Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.

Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.

Step 7 Disconnect power from the access point.

Step 8 Press and hold MODE while you reconnect power to the access point.

Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.

Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

To add on this:

A complete thread where I explained the steps:

http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless - Mobility&topic=Getting Started with Wireless&CommCmd=MB?cmd=pass_through&location=outline@^1@@.2cd4432e/8#selected_message

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

thanks! i've downloaded these at cisco.com website. just want to verify if these IOS image are autonomous:

c1130-k9w7-tar.124-10b.JDA.tar

c1130-k9w7-tar.124-3g.JA1.tar

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

Correct

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

awesome! i've just made LW AP to autonomous! thanks for your help.

Hall of Fame Super Gold

Re: Change IOS on 1131AG AP from Lightweight to Autonomous

Thanks for the ratings.

2582
Views
0
Helpful
6
Replies
CreatePlease login to create content