Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Changing WPA Username and Password

Hi Guys,

I am quite new to Wireless. would appriciate any help on this issue.

I am using a 891w as autonomous AP. I got some basic config from support forum.. Once configuration was done, i could see the SSID; but it was asking for username which i could not figure out. Here is the config below.

hostname ap

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid WirelessNetwork

   vlan 1

   authentication open

   authentication key-management wpa

   guest-mode

   mbssid guest-mode

   wpa-psk ascii 7 cisco

!

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption vlan 1 mode ciphers aes-ccm

!

encryption mode ciphers aes-ccm

!

broadcast-key vlan 1 change 30

!

!

ssid WirelessNetwork

!       

antenna gain 0

station-role root

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio1

no ip address

no ip route-cache

!

encryption vlan 1 mode ciphers aes-ccm

!

encryption mode ciphers aes-ccm

!

broadcast-key vlan 1 change 30

!       

!

ssid Wirelessnetwork

!

antenna gain 0

dfs band 3 block

channel dfs

station-role root

!

interface Dot11Radio1.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router

no ip address

no ip route-cache

!

interface GigabitEthernet0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address dhcp client-id GigabitEthernet0

no ip route-cache

!

cns dhcp

end

Please help me change the username and password for the SSID.

I hope in the able example the password is cisco.

--

Thanks you.

4 REPLIES
Gold

Changing WPA Username and Password

Hi,

This should be asking you only the password not the username as you have confired with wpa-psk. What client device are you testing this with? If this is wondows machine please choose your sececurity as WPA-Personal on the wireless profile and then it would asked for the Security Key..You will have to enter your password there. The password from the configuration i can see it as cisco.

wpa-psk ascii 7 cisco

Hope thats helos,

Regards

Najaf

Please rate when applicable or helpful !!!

New Member

Re: Changing WPA Username and Password


Najaf KC wrote:

If this is wondows machine please choose your sececurity as WPA-Personal on the wireless profile and then it would asked for the Security Key.]\

where should i change this? Is it on the windows or CLI of the router?

could you show me an example?

Gold

Changing WPA Username and Password

Hi,

You didnt tell me what wireless client device are you using?? If this is windows PC change this on your PC wireless profile configuration.

For Windows below is the example

Regards

Najaf

Please rate when applicable or helpful !!!

New Member

Re: Changing WPA Username and Password

sorry it was an Andriod Phone!

k let me try with a PC

232
Views
10
Helpful
4
Replies
CreatePlease to create content