Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 2106 WLC / 1252 LAP

Hi folks,

Probably a dumb mistake here, but hoping someone can offer some advice.

So I have a new 2106 configured, and just connected a 1252 directly to port 8 (POE). While I do see the link come up (Ports on the management GUI) the AP does not seem to register. As far as I can tell, everything is configured properly. Not sure why the 1252 won't register.

Also noteworthy: this is the second 2106 in this particular office - DHCP option 43 has the address of both WLC's in the scope.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Cisco 2106 WLC / 1252 LAP

whats is the output of the command "show port summary" on the WLC?

Regards

Surendra

6 REPLIES
Cisco Employee

Re: Cisco 2106 WLC / 1252 LAP

First check point... * is the APs getting the IP address?? sh cdp neighbors command will let us know..

Regards

Surendra

Cisco Employee

Re: Cisco 2106 WLC / 1252 LAP

whats is the output of the command "show port summary" on the WLC?

Regards

Surendra

New Member

Re: Cisco 2106 WLC / 1252 LAP

CDP:

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID

ap               Fastethernet0/0/8 137            T I     AIR-AP125 Gig 0

Port Summary:


           STP   Admin   Physical   Physical   Link   Link
Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE
-- ------- ---- ------- ---------- ---------- ------ ------- ---------
1  Normal  Forw Enable  Auto       100 Full   Up     Enable  N/A
2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A
3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A
4  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A
5  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A
6  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A
7  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off)
8  Normal  Forw Enable  Auto       100 Full   Up     Enable  Enable  (Power On

New Member

Re: Cisco 2106 WLC / 1252 LAP

Also, we are running software rev 7.0.98.0.

Best,

Carl

New Member

Re: Cisco 2106 WLC / 1252 LAP

-------------------------
Device ID: ap
Entry address(es): x.x.x.x (IP confirmed)
Platform: cisco AIR-AP1252AG-A-K9   ,  Capabilities: Trans-Bridge IGMP
Interface: Fastethernet0/0/8,  Port ID (outgoing port): GigabitEthernet0
Holdtime : 179 sec

Version :
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Sun 07-Jun-09 03:50 by prod_rel_team

--More-- or (q)uit

Advertisement version: 1
Duplex: Half

New Member

Re: Cisco 2106 WLC / 1252 LAP

Yep, was a dumb mistake - my user actually purchased the autonomous model and not the LWAP version. Got that converted over to LW and we are rockin and rolling.

Thanks for the reply!

1265
Views
0
Helpful
6
Replies