Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco 4402 LAP1131 Interference Profile Failed for Base Radio MAC:

Dropped connections every day, few times a day.
WLC Was working perfectly fine for about a year then had some dropped connections.
Upgraded to the latest firmaware and also default it to the factory and reconfigured it.
Same problem!

Cisco 4402
Software Version 7.0.98.0

8x Cisco: AIR-LAP1131AG-A-K9 also v/7.0.98.0

Interference Profile Failed for Base Radio MAC:

9 REPLIES
Cisco Employee

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

Hi,

In general the Interference Profile message occurs when the noise or interference in the area of an AP has risen over the threshold value.

This value can be configured in Wireless > 802.11a/n | 802.11b/g/n > RRM > General

lemme know if this answered your question..

Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull


New Member

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

Yes,

I have seen the setting for noise. its set to -70 by default. What would be more appropriate setting?

New Member

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

Dropped AP-WLC connections ? or dropped client connections ? If its latter, interference might be an issue. Did you introduce any new wireless devices into the network operating in 802.11 frequencies ? (like wireless meeting room systems etc..)

regards

Joe

New Member

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

I have clients that are complaining that they loose network connection, and yes I do have many new laptops and Apple Ipads.

This is what I'm seeing now (WPA MIC Error counter measure activated on Radio with MAC 00:22:55:58:85:b0 and Slot ID 0. Station MAC Address is 60:33:4b:46:f0:06 and WLAN ID is 1)

New Member

Cisco 4402 LAP1131 Interference Profile Failed for Base Radio MA

I have the same problem with WLC5508 "

"Interference Profile failed".

Any update for help!.

Thanks.

Hall of Fame Super Silver

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

This is a threshold parameter: "Interference Profile failed" along with some others.  All this does is send alerts to the WLC log, to your syslog or to your WCS/NCS or Prime Infrastructure management tool.  You need to adjust these for your environment if you see too many alerts being triggered.  Interference can be a main issue in downtown big citites and you would bump the value up to reduce the number of alerts you see.  Yes interference will cause issues, but this is an alert threshold and will not fix your interference, just tell you that you have interference due to hitting the X value.

1.jpg

Thanks,

Scott

*****Help out other by using the rating system and marking answered questions as "Answered"*****

-Scott
*** Please rate helpful posts ***
VIP Purple

Re: Cisco 4402 LAP1131 Interference Profile Failed for Base Radi

Scott

Can you please check your PM.

Regards

Hall of Fame Super Silver

Cisco 4402 LAP1131 Interference Profile Failed for Base Radio MA

Okay...

Thanks,

Scott

*****Help out other by using the rating system and marking answered questions as "Answered"*****

-Scott
*** Please rate helpful posts ***
New Member

Do an alarm will be raised if

Do an alarm will be raised if there are more than 12 clients connected to the radio by default?

17622
Views
8
Helpful
9
Replies
CreatePlease login to create content