Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Hello good people. I have recently bought Cisco AIR CAP3502I E K9 but i am seeing that it can only work with WLAN controller. How can I make it work as a stand alone.

Your help will be appreciated.

23 REPLIES
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Any good links on how i can start configuring it as standalone WAP

Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

Take a look at this

https://supportforums.cisco.com/docs/DOC-20537

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

You can use the 1260 autonomous code if you want. Just remember, this isn't supported by Cisco but it will work.

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
Cisco Employee

Cisco AIR CAP3502I E K9--- standalone Config

U can convert but not supported by TAC!!

use the below link..

https://supportforums.cisco.com/docs/DOC-14960

Please dont forget to rate the usefull posts!!

Regards

Surendra

Community Member

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott whats the autonomous code 1260 for and how is it used. I have never confugured a cisco wirelsess AP

Community Member

Re: Cisco AIR CAP3502I E K9--- standalone Config

This information is so helpful. Last part is where can i get

cisco IOS for 1260 ap3g1-k9w7-tar.124-25d.JA1

Don have smartnet account

Hall of Fame Super Silver

Cisco AIR CAP3502I E K9--- standalone Config

Send me an email you on that.

-Scott
*** Please rate helpful posts ***
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Team confirm that after this conversion to standalone it can pass traffic. I have read some text which say it cannot pass traffic.

Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

Where did you read that? You should have no issue since the 3502 radios are the same as the 1260. You just won't have the full feature of the 3502.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Thanks Fella.

Any document showing how to finish off the configs after the IOS chnage. The howto docs for 1260/3502 for stand alone most i am seeing are for controller based. Have never setup a cisco WAP but i understanda and am into cisco

Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

You can reference this guide for the 1140

http://www.cisco.com/en/US/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html

http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37ssid.html

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

Here is a link from George's blog page

http://www.my80211.com/home/2011/11/18/autonomous-ios-support-for-3500-and-3600-series-access-point.html

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

I am still having troubles with this issue.

Scott kindly resend the image again as it should be uploaded.

Another challenges is setting the ip address go g0 interface. Even though i do that manually dhcp continues to discard the manual n gets smthing from my dhcp since it will continously look for WController.

How do i sort this out.

I have also failed to access the GUI thru the private ip add

Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Looks like the file is now extracting. Thanks Scott.

one last problem is how do i stop renew of IP address.

I have assigned the address manually but its being overwritten by the DHCP ip which renews afters a minute.

Solving this should make me a happy man.

Hall of Fame Super Silver

Re: Cisco AIR CAP3502I E K9--- standalone Config

Here is how to configure an ip address to the bvi1 interface.

Command

Purpose

Step 1

configure terminal

Enter global configuration mode.

Step 2

interface bvi1

Enters interface configuration mode for the BVI.

Step 3

ip address ip_address net_mask

Assigns an IP address and subnet mask address to the BVI.

http://www.cisco.com/en/US/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html#wp42920

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Happy New year,

My 3502 AP is not accepting config t

on show int brief its also showing Ge0 only and  no bvi is shown.

What do i need to do for it to accept config t command

Community Member

Cisco AIR CAP3502I E K9--- standalone Config

I have entered the following command

debug capwap console cli

and have manged to configure the ip address for Ge0 manually

This address is however renewed after some few minutes to a dhcp assigned  which is also continously renewed.

What should i do to stabilise this assignment.

Hall of Fame Super Gold

Cisco AIR CAP3502I E K9--- standalone Config

What do i need to do for it to accept config t command

What are you trying to do?  3500 does NOT "support" autonomous IOS.  When I mean "support", I mean you can load autonomous IOS but don't get Cisco TAC to help you with any configuration issues.

Community Member

Cisco AIR CAP3502I E K9--- standalone Config

Got the autonomous IOS running now.

last issues is how do i enbale POe.

The deployment place has no power but the network cable has been laid to the place.

its running 1260 IOS

Hall of Fame Super Silver

Cisco AIR CAP3502I E K9--- standalone Config

You don't need to enable PoE on the AP's.  If your switch is PoE then it should power up your AP.  If your switch isn't PoE, then you can't enable anything, you will need to use a power injectior or an AC power adapter.

-Scott
*** Please rate helpful posts ***
Community Member

Cisco AIR CAP3502I E K9--- standalone Config

i am using cisco 2960G switch.

what commands should i use to enable POe on a port.

Hall of Fame Super Gold

Cisco AIR CAP3502I E K9--- standalone Config

i am using cisco 2960G switch.

You sure about this model?  Can you post the output to the command "sh inventory" of your switch?

Cisco DOES NOT make a 2960G model with PoE.  Except the 2960S, all 2960 PoE variety are 10/100BaseTx.

If this is the case, then in order to power up the 3500 you'll need to either purchase a power brick or the PWR-INJ3.

18163
Views
0
Helpful
23
Replies
CreatePlease to create content