Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Clients on 1131AG cannot talk to each other

I have a dozen clients on an 1131AG and they cannot ping each other.  I get a reply but it says destination host unreachable.  Any ideas on how to resolve this?  Here is my config:

                  

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname MediaRoom

!

no logging console

!

aaa new-model

!

!

aaa group server radius rad_eap

!

aaa group server radius rad_mac

!

aaa group server radius rad_acct

!

aaa group server radius rad_admin

!

aaa group server tacacs+ tac_admin

!

aaa group server radius rad_pmip

!

aaa group server radius dummy

!

aaa authentication login default local

aaa authentication login eap_methods group rad_eap

aaa authentication login mac_methods local

aaa authorization exec default local

aaa accounting network acct_methods start-stop group rad_acct

!

aaa session-id common

no ip domain lookup

!

!

!

dot11 ssid AJPL Training

authentication open

!

power inline negotiation prestandard source

!

!

username extreme privilege 15 secret 5

username admin privilege 15 password 7

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption key 1 size 40bit 7 A1E447FB3D18 transmit-key

encryption mode wep mandatory

!

ssid AJPL Training

!

station-role root

beacon dtim-period 1

bridge-group 1

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio1

no ip address

no ip route-cache

shutdown

!

encryption key 1 size 40bit 7 D71318FE4B24 transmit-key

encryption mode wep mandatory

!

ssid AJPL Training

!

dfs band 3 block

channel dfs

station-role root

rts threshold 2312

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface FastEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address 172.16.3.15 255.255.255.0

no ip route-cache

!

ip default-gateway 172.16.3.1

ip http server

ip http authentication aaa

no ip http secure-server

ip http help-path

http://www.cisco.com/warp/public/779...onfig/help/eag

ip radius source-interface BVI1

radius-server attribute 32 include-in-access-req format %h

radius-server vsa send accounting

bridge 1 route ip

!

!

banner motd C

************************************************************ ***************

* L E G A L N O T I C E -- Y O U M U S T R E A D *

************************************************************ ***************

* *

* You must have explicit permission to access or configure this *

* device. All activities performed on this device are monitored *

* and logged. Violations of the *

* security policy may result in criminal prosecution. *

************************************************************ ***************

* *

* Anyone using this system expressly consents to such monitoring and is *

* advised that if such monitoring reveals possible evidence of criminal *

* activity, system personnel may provide the evidence of such monitoring *

* to law enforcement officials. *

* *

************************************************************ ***************

* UNAUTHORIZED ACCESS TO THIS NETWORK DEVICE IS PROHIBITED *

************************************************************ ***************

!

line con 0

line vty 5 15

!

end
Everyone's tags (5)
4 REPLIES

Re: Clients on 1131AG cannot talk to each other

Welcome to CSC

I will assume you are authenticated to the access point and this is not an issue. As for the ap, its like a switch. Can you bridge this vlan subnet on the wired and ping the wireless devices? Sounds more like a routing issue to me, but they are on the same subnet. Check the wired side and see if that work first.

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________
Community Member

Re: Clients on 1131AG cannot talk to each other

Thanks.

Yes, the clients have authenticated and they are getting the proper network settings via the DHCP server.

From the clients connected wirelessly, I can ping wired clients on the same subnet.

From the clients connected by ethernet, I can ping the wireless clients on the same subnet.

I just can't get the wireless clients to talk to each other.

I plugged in a Linksys WAP54G and connected the wireless clients to it and they can communicate fine, so I assume there is something in the config (or something not in the config) that is preventing them from communicating with each other.

Clients on 1131AG cannot talk to each other

https://supportforums.cisco.com/docs/DOC-3212

Rating useful replies is more useful than saying "Thank you"
Hall of Fame Super Red

Clients on 1131AG cannot talk to each other

Hi Anthony,

Just to add a note to the great tips from my friends George and Amjad (+5 )

I might try this doc as well;

https://supportforums.cisco.com/docs/DOC-4823

Cheers!

Rob

"Always movin' ahead and never lookin' back" - Springsteen

727
Views
10
Helpful
4
Replies
CreatePlease to create content