Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Configure as a repeater

Hello,

I have to configure a second AP as a repeater, and these are the steps that I done:

1- the 1st AP is working as autonomous AP

2- the seconde one i make it associated with the SSID of the 1st AP

3-I configured the roll of the 2nd AP as repeater

I think that this only are the steps to do it, as all the two AP are in standard configuration.

Is there any other step to do to configure the AP as repeater??

1 ACCEPTED SOLUTION

Accepted Solutions
New Member

Re: Configure as a repeater

Hi omar,

Pls go through the below mentioed link.

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/accsspts/ap350scg/ap35ch12.htm

It may help you

Regds

Saji k.s

6 REPLIES
Hall of Fame Super Red

Re: Configure as a repeater

Hi Omar,

Here is a Step by Step guide that might help;

Configuring a Repeater Access Point

From this good doc;

http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a0080341cfd.html#wp1034763

Hope this helps!

Rob

New Member

Re: Configure as a repeater

Hello Rob,

This step are the same of what I did. But at the end the Repeater cannot associate to the AP ??

I'll try all the steps for a second time (after the weedend I'll do it) and I'll send you a reply if that will work.

Thank you anyway.

New Member

Re: Configure as a repeater

Hi omar,

Pls go through the below mentioed link.

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/accsspts/ap350scg/ap35ch12.htm

It may help you

Regds

Saji k.s

New Member

Re: Configure as a repeater

This is a part of the configuration file of the AP configured as a repeater :

(On the root, I have a default configuration with an SSID : DJEZZY Wifi Hotspot. unless I did all the steps, but I can't arrive to associate the Repeater to the root)

Note : the APs have all the default configuration.

CONFIG FILE:

Current configuration : 1218 bytes

!

version 12.3

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

dot11 ssid DJEZZY Wifi Hotspot

infrastructure-ssid optional

!

bridge irb

!

interface Dot11Radio0

no ip address

no ip route-cache

shutdown

!

ssid DJEZZY Wifi Hotspot

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role repeater

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface BVI1

no ip address

no ip route-cache

!

Regards,

Omar,

New Member

Re: Configure as a repeater

that guide is no help at all or my aironet 1242 is broken.

New Member

Re: Configure as a repeater

Do you have the same problem to configure a repeater??

You use what kind of security??

Can you post the part of the SSID ??

I have fixed my problem as I'm using Open Authentication.

Regards,

231
Views
5
Helpful
6
Replies
CreatePlease login to create content