Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

connect air-sap-1602i-e-k9 to wlc 2504

Hi,

not able to connect this AP´s to wlc 2504 with 7.4.121

Ap gets an dhcp but does not show up in controller never!

nothing happens on controller side. Below is a shot of AP booting process...

Could you help?

"ap boot":

Boot from flash

IOS Bootloader - Starting system.

FLASH CHIP: Spansion S25FL256

Xmodem file system is available.

flashfs[0]: 181 files, 7 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31936000

flashfs[0]: Bytes used: 10419200

flashfs[0]: Bytes available: 21516800

flashfs[0]: flashfs fsck took 10 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: c0:8c:60:29:9b:92

************* loopback_mode = 0

Loading "flash:/ap1g2-k9w7-mx.152-2.JB2/ap1g2-k9w7-mx.152-2.JB2"...#############                             ################

File "flash:/ap1g2-k9w7-mx.152-2.JB2/ap1g2-k9w7-mx.152-2.JB2" uncompressed and i                             nstalled, entry point: 0x100000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE S                             OFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Mon 29-Jul-13 12:16 by prod_rel_team

Initializing flashfs...

FLASH CHIP: Spansion S25FL256

flashfs[3]: 181 files, 7 directories

flashfs[3]: 0 orphaned files, 0 orphaned directories

flashfs[3]: Total bytes: 31808000

flashfs[3]: Bytes used: 10419200

flashfs[3]: Bytes available: 21388800

flashfs[3]: flashfs fsck took 9 seconds.

flashfs[3]: Initialization complete.

flashfs[4]: 0 files, 1 directories

flashfs[4]: 0 orphaned files, 0 orphaned directories

flashfs[4]: Total bytes: 11999232

flashfs[4]: Bytes used: 1024

flashfs[4]: Bytes available: 11998208

flashfs[4]: flashfs fsck took 0 seconds.

flashfs[4]: Initialization complete....done Initializing flashfs.

Warning:  the compile-time code checksum does not appear to be present.

Radio0  present 8764B 8000 0 A8000000 A8010000 0

Rate table has 180 entries (48 SGI/72 BF variants)

Radio1  present 8764B 8000 0 88000000 88010000 4

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Warning:  the compile-time code checksum does not appear to be present.

cisco AIR-SAP1602I-E-K9    (PowerPC) processor (revision B0) with 98294K/32768K                              bytes of memory.

Processor board ID FGL1738W5CE

PowerPC CPU at 533Mhz, revision number 0x2151

Last reset from power-on

1 Gigabit Ethernet interface

2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: C0:8C:60:29:9B:92

Part Number                          : 73-14671-04

PCA Assembly Number                  : 000-00000-00

PCA Revision Number                  :

PCB Serial Number                    : FOC17374RRW

Top Assembly Part Number             : 800-38552-01

Top Assembly Serial Number           : FGL1738W5CE

Top Revision Number                  : A0

Product/Model Number                 : AIR-SAP1602I-E-K9

utoconfig enabled device!!!

*Mar  1 00:00:17.067: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:18.067: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

*Mar  1 00:01:03.923: Starting Ethernet promiscuous mode

*Mar  1 00:01:03.995: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down

*Mar  1 00:01:03.995: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down

*Mar  1 00:01:04.007: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Mon 29-Jul-13 12:16 by prod_rel_team

*Mar  1 00:01:04.007: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start

*Mar  1 00:01:04.039: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar  1 00:01:04.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

*Mar  1 00:01:04.995: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar  1 00:01:04.995: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar  1 00:01:13.091: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.50.2.174, mask 255.255.0.0, hostname ap

12 REPLIES
VIP Purple

Re: connect air-sap-1602i-e-k9 to wlc 2504

Hi

Your AP have autonomus image.

To connect with WLC you need to to convert this AP to LAP.

Reagrds

New Member

Re: connect air-sap-1602i-e-k9 to wlc 2504

HI

How can that be done?

VIP Purple

Re: connect air-sap-1602i-e-k9 to wlc 2504

Check this :

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE S                             OFTWARE (fc1)

  • k9w7 - autonomous (or "site survey") IOS
  • k9w8 - full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on "mesh" APs)
  • rcvk9w8 - lightweight recovery image - this is factory installed on lightweight APs, unless a "mesh" image is specified; it lacks radio firmware

You need k9w8 image on AP.

How to convert to LAP.

For the LWAP conversion, use the recovery image ( e.g  -rcvk9w8-tar.).  use the command on the autonomous AP priviledge mode.

AP#archive download-sw /force-reload /overwrite tftp://10.10.10.1/c1600-rcvk9w8

or

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html

Regards

New Member

Re: connect air-sap-1602i-e-k9 to wlc 2504

ok have the file, the tftp

password for enable on ap ?

Cisco is making it tuff!

VIP Purple

connect air-sap-1602i-e-k9 to wlc 2504

Password is : Cisco

Enable password is also : Cisco

C, first later is capital.

make sure that u have recovery image.

Regards

New Member

Re: connect air-sap-1602i-e-k9 to wlc 2504

is it possible to change IP address of the AP?

it gets dhcp but then loses the ping it after the boot

VIP Purple

Re: connect air-sap-1602i-e-k9 to wlc 2504

did you changed the AP to Lightweight ??

Here are the commands:

AP#capwap ap ip address  
AP#capwap ap ip default-gateway 
AP#capwap ap controller ip address 
AP#capwap ap hostname 

Regards

New Member

Re: connect air-sap-1602i-e-k9 to wlc 2504

Hi Sorry ,

I did not yet changed because i loose connectivity when ap boots

archive download-sw /overwrite /force-reload tftp://10.50.2.179/ap1g2-rcvk9w8-tar.152-4.JB3.tar

My PC is dhcp on 10.50.2.179 and ap is 10.50.2.174..

But in the middle it looses connectivity and i cant run fully the extracting...

Regards

VIP Purple

Re: connect air-sap-1602i-e-k9 to wlc 2504

Try to change the image as per my last posts links.

Let me know the outcome.

If you face any problem then please write back here.

Regards

New Member

Re: connect air-sap-1602i-e-k9 to wlc 2504

But can´t I change the IP  of the AP to static just for the conversion ?

AP config ??

VIP Purple

Re: connect air-sap-1602i-e-k9 to wlc 2504

HI,

Resetting to Default Settings Using the MODE Button

Follow these steps to reset the access point to factory default settings using the access point MODE button:


Step 1 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Step 2 Press and hold the MODE button while you reconnect power to the access point.

Step 3 Hold the MODE button until the Status LED turns amber (approximately 1 to 2 seconds), and release the button. All access point settings return to factory defaults.

follow this posts:

http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/

Regards

1827
Views
0
Helpful
12
Replies