Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Dot11Radio0 is reset

Anyone know how to rest the Dot11Radio?

I have also try to config the power level but it prompt me that the selection is invalid.

Dot11Radio0 is reset, line protocol is down

Hardware is 802.11G Radio, address is 0000.0000.0000 (bia 0000.0000.0000)

MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set

ARP type: ARPA, ARP Timeout 04:00:00

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/30 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

DOT11-2-RESET_RADIO: Interface Dot11Radio0, Radio won't start, Trying hardware reset on radio

%SYS-3-CPUHOG: Task is running for (1996)msecs, more than (2000)msecs (4/4),process = Dot11 driver.

-Traceback= 23F878 23F860 40AC60 679960 67C634 413FA4 41B2A8 1357B0

%SYS-3-CPUHOG: Task is running for (3995)msecs, more than (2000)msecs (4/4),process = Dot11 driver.

-Traceback= 23F858 23B644 40AC60 679960 67C634 413FA4 41B2A8 1357B0

%SYS-3-CPUHOG: Task is running for (5994)msecs, more than (2000)msecs (5/4),process = Dot11 driver.

-Traceback= 23F860 23B644 40AC60 679960 67C634 413FA4 41B2A8 1357B0

%DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available

%DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available

10 REPLIES

Re: Dot11Radio0 is reset

Looks like you could have a hardware issue on that radio, I would send it back to your supplier.

HTH>

Re: Dot11Radio0 is reset

Hi

do you have a POWER INJECTOR?

If a power-injector is installed, issue the command under CLI:"

"power inline negotiation injector installed"

Best regardas

New Member

Re: Dot11Radio0 is reset

have you assigned a SSID to the DotRadio0 interface, if not the interface will show a status of reset

New Member

Re: Dot11Radio0 is reset

The access point already have an SSID. For your info, the access point also support DotRadio 1 for A channel.

The DotRadio 1 does not have this issue and is working fine.

I have tried to type in "power inline negotiation" but the version does not support it.

I guess the card is faulty.

New Member

Re: Dot11Radio0 is reset

Its not faulty. The IOS upgrade just didn't complete properly. Push IOS to it again and the radio driver will push to the radio. When you reboot you will have a happy AP.

New Member

Re: Dot11Radio0 is reset

Do you mean that the IOS is corrupt?

Hall of Fame Super Silver

Re: Dot11Radio0 is reset

Kian,

It's your configuration that is the issue. I loaded you config that you posted on the other thread:

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&topicID=.ee7c7c3&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc1912b

And I got the same error you are seeing. The interfaces are configured wrong. Make the changes to the configuration and the interface will be up.

-Scott
*** Please rate helpful posts ***
New Member

Re: Dot11Radio0 is reset

It still does not help even if i clear and change the configuration. Still receive:

*Mar 1 00:01:53.230: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available

*Mar 1 00:01:53.230: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available

*Mar 1 00:01:53.231: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar 1 00:02:14.362: %DOT11-2-RESET_RADIO: Interface Dot11Radio0, Radio won't start, Trying hardware reset on radio

*Mar 1 00:02:16.360: %SYS-3-CPUHOG: Task is running for (1998)msecs, more than (2000)msecs (0/0),process = Dot11 driver.

-Traceback= 23F850 23B644 40AC60 679960 67C634 413FA4 41B2A8 1357B0

*Mar 1 00:02:18.359: %SYS-3-CPUHOG: Task is running for (3997)msecs, more than (2000)msecs (0/0),process = Dot11 driver.

-Traceback= 243BF0 23F860 23B644 40AC60 679960 67C634 413FA4 41B2A8 1357B0

*Mar 1 00:02:20.358: %SYS-3-CPUHOG: Task is running for (5996)msecs, more than (2000)msecs (0/0),process = Dot11 driver.

-Traceback= 243BE8 23F858 23B644 40AC60 679960 67C634 413FA4 41B2A8 1357B0

*Mar 1 00:02:28.559: %LINK-3-UPDOWN: Interface BVI1, changed state to up

Hall of Fame Super Silver

Re: Dot11Radio0 is reset

Don't know.... I used your config on an ap I had and I got the same error you are seeing. I adjusted the config and I got it to work... Post the config you have on now.

-Scott
*** Please rate helpful posts ***
New Member

Dot11Radio0 is reset

I had the same issue

power inline negotiation prestandard source

solved it

8497
Views
0
Helpful
10
Replies
CreatePlease login to create content