Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0?  I have looked through all the reports and I cannot find a report that gives me the CDP neighbor information of an access point.  I thought that information was in there, however I cannot seem to find it.

 

Thanks in advance!

2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

HiYou can get this from an

Hi

You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.

Regards

Rasika

**** Pls rate all useful responses ****

 

Hall of Fame Super Silver

Rasika shows you how to get

Rasika shows you how to get that info from PI 2.1... but you have to customize the report to get the neighbor info.

I tend to run reports like that from the WLC itself to a spreadsheet I have created.  I run the show ap cdp neighbor all on the cli of each WLC and put that information in a spreadsheet.

 

-Scott
*** Please rate helpful posts ***
10 REPLIES
Hall of Fame Super Gold

Odd.  If you click the AP in

Odd. 

 

If you click the AP in question, you should have a tab called "CDP Neighbors".  

New Member

I should be more clear.  I

I should be more clear.  I don't want to look for a single access point.  I want a report on 4212 access points and don't want to go through each access point and find out its neighbor.  I thought it could be done through PI.

Hall of Fame Super Gold

Let me get back to you on

Let me get back to you on this.  

 

What you are asking for CAN BE DONE.  I've done it before with WCS so I'm sure it can be done with PI.

New Member

I agree!  I thought it could

I agree!  I thought it could be done also.  I believe I used to do it in WCS as well.  However, yesterday I looked at PI to run a report on CDP neighbor information to help track down some access point locations that lost their configs, and discovered that I could not find the report that showed me 
CDP information on the access points.

Hall of Fame Super Gold

Try this:  Go to Monitor >

Try this: 

 

Go to Monitor > Access Points. 

 

You should see in the upper left-hand corner a blue box called "Edit View".  Click that and choose the option you want enabled.

VIP Purple

HiYou can get this from an

Hi

You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.

Regards

Rasika

**** Pls rate all useful responses ****

 

Hall of Fame Super Silver

Rasika shows you how to get

Rasika shows you how to get that info from PI 2.1... but you have to customize the report to get the neighbor info.

I tend to run reports like that from the WLC itself to a spreadsheet I have created.  I run the show ap cdp neighbor all on the cli of each WLC and put that information in a spreadsheet.

 

-Scott
*** Please rate helpful posts ***
Bronze

Hi,Collectively Rasika and

Hi,

Collectively Rasika and Scott comment is answer of your query

please check and run the report by his way, hopefully you will find CDP information by this way.

Yes, you can get the CDP

Yes, you can get the CDP neighbor information.

You need to go to Report-> Report Lauch pad-> Device -> Inventory -> Inventory Report Details

New Member

very cool stuff... esp for

very cool stuff... esp for gazillions of ap's

been using this tool since wcs and now, just very recent, with pi2.0...

 

1795
Views
5
Helpful
10
Replies