Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

MC 3850 and AP 3700 join issue

I have   02 WS-C3850-48U stacked  and a single AP C3700 directly connected.

The problem is AP  seems to join and then fails again, this state repeating.  

Any suggections would be appreciated.

Here are some details:

MLVN-ACCESS-P1#sh license right-to-use 
 Slot#  License name   Type     Count   Period left 
----------------------------------------------------------
 1      ipbase       permanent     N/A   Lifetime
 1      apcount      adder         8     Lifetime

License Level on Reboot: ipbase


 Slot#  License name   Type     Count   Period left 
----------------------------------------------------------
 2      ipbase       permanent     N/A   Lifetime
 2      apcount      adder         8     Lifetime

License Level on Reboot: ipbase

 

MLVN-ACCESS-P1#sh cdp neighbors detail 
-------------------------
Device ID: AP58f3.9c27.4d48
Entry address(es): 
  IP address: 10.9.9.2
Platform: cisco AIR-CAP3702I-E-K9,  Capabilities: Router Trans-Bridge 
Interface: GigabitEthernet2/0/21,  Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 168 sec

Version :
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.2(4)JB5h, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 16-Apr-14 01:15 by prod_rel_team

advertisement version: 2
Duplex: full
Power drawn: 16.800 Watts
Power request id: 23984, Power management id: 2
Power request levels are:16800 15400 13000 0 0 
Management address(es):

 


MLVN-ACCESS-P1(config)#do sh ap summary 
Number of APs: 1

Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured

AP Name                           AP Model  Ethernet MAC    Radio MAC       State         
----------------------------------------------------------------------------------------
AP58f3.9c27.4d48                  3702I     58f3.9c27.4d48  58f3.9c3a.2070  Registered    


MLVN-ACCESS-P1(config)#do sh ap summary 
Number of APs: 0

Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured

 

MLVN-ACCESS-P1(config)#do sh ap summary 
Number of APs: 0

Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured

......

MLVN-ACCESS-P1(config)#do sh ap summary 
Number of APs: 1

Global AP User Name: Not configured
Global AP Dot1x User Name: Not configured

AP Name                           AP Model  Ethernet MAC    Radio MAC       State         
----------------------------------------------------------------------------------------
AP58f3.9c27.4d48                  3702I     58f3.9c27.4d48  58f3.9c3a.2070  Registered    

 

The Logging:

         
Log Buffer (16384 bytes):
77: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:13:40.274: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:13:40.708: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:13:40.942: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:13:41.698: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:13:41.711: %ILPOWER-7-DETECT: Interface Gi1/0/19: Power Device detected: Cisco PD
*Oct 23 19:13:41.817: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:13:42.043: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:13:42.075: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:13:42.762: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:13:42.953: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/9: Power granted
*Oct 23 19:13:43.664: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:13:43.665: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:13:46.101: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:13:46.101: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:13:46.102: *%LOG-3-Q_IND: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:13:46.102: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:13:46.102: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:13:46.102: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:13:46.102: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP 58:f3:9c:3a:20:70  
*Oct 23 19:13:46.104: *%CAPWAP-3-POST_DECODE_ERR: 1 wcm:  Post decode processing failed for Config status from AP 58f3.9c3a.2070  
*Oct 23 19:13:46.112: %LINK-3-UPDOWN: Interface Capwap0, changed state to up
*Oct 23 19:13:46.121: *%CAPWAP-3-DATA_TUNNEL_UPDATE_ERR1: 1 wcm:  Failed to send CAPWAP data tunnel update for AP: 58f3.9c3a.2070 with interface id: 0xd1724000000537. Reason: No QoS Policy Installation since AP connection is being deleted!   
*Oct 23 19:13:46.121: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Configuration Update Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:13:46.215: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:13:46.964: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:13:47.112: %LINEPROTO-5-UPDOWN: Line protocol on Interface Capwap0, changed state to up
*Oct 23 19:13:47.749: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:13:49.002: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:13:49.858: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:13:50.004: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:13:50.182: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:13:50.344: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:13:50.456: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/28: Power granted
*Oct 23 19:13:50.668: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:13:50.695: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/29: PD removed
*Oct 23 19:13:50.696: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/29: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:13:51.769: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:13:52.104: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:13:52.134: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:13:52.916: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:13:52.916: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:13:53.366: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/21: PD removed
*Oct 23 19:13:53.367: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/21: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:13:53.752: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:13:56.361: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:13:56.808: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/34: Power granted
*Oct 23 19:13:57.714: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/19: PD removed
*Oct 23 19:13:57.715: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/19: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:13:57.838: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:13:58.724: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:13:59.072: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:13:59.173: %ILPOWER-7-DETECT: Interface Gi1/0/29: Power Device detected: Cisco PD
*Oct 23 19:13:59.283: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:13:59.819: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:13:59.819: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/28: Power granted
*Oct 23 19:14:00.072: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:14:00.234: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:14:00.829: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:14:00.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Capwap0, changed state to down
*Oct 23 19:14:01.492: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:14:01.871: %ILPOWER-7-DETECT: Interface Gi1/0/21: Power Device detected: Cisco PD
*Oct 23 19:14:02.202: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:14:02.317: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:14:03.884: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:14:06.214: %ILPOWER-7-DETECT: Interface Gi1/0/19: Power Device detected: Cisco PD
*Oct 23 19:14:06.432: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:14:06.877: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/34: Power granted
*Oct 23 19:14:07.879: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:14:08.124: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:14:08.792: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:14:09.144: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:14:09.788: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:14:09.790: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:14:09.907: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:14:10.892: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:14:11.944: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:14:12.262: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:14:12.750: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:14:13.064: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:14:15.174: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/29: PD removed
*Oct 23 19:14:15.175: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/29: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:16.163: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:14:16.612: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:14:16.612: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:16.613: *%LOG-3-Q_IND: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:16.613: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:14:16.613: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:14:16.613: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:16.613: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:16.614: *%CAPWAP-3-POST_DECODE_ERR: 1 wcm:  Post decode processing failed for Config status from AP 58f3.9c3a.2070  
*Oct 23 19:14:16.622: %LINK-3-UPDOWN: Interface Capwap0, changed state to up
*Oct 23 19:14:16.635: *%CAPWAP-3-DATA_TUNNEL_UPDATE_ERR1: 1 wcm:  Failed to send CAPWAP data tunnel update for AP: 58f3.9c3a.2070 with interface id: 0xd6bec000000538. Reason: No QoS Policy Installation since AP connection is being deleted!   
*Oct 23 19:14:16.635: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Configuration Update Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:14:16.727: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:14:16.844: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/34: Power granted
*Oct 23 19:14:17.623: %LINEPROTO-5-UPDOWN: Line protocol on Interface Capwap0, changed state to up
*Oct 23 19:14:17.873: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/21: PD removed
*Oct 23 19:14:17.874: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/21: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:17.958: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:14:18.192: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:14:18.255: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:14:18.325: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:14:19.152: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/36: Power granted
*Oct 23 19:14:19.357: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:14:19.357: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/28: Power granted
*Oct 23 19:14:19.970: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:14:19.972: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:14:20.088: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:14:20.284: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:14:21.002: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/9: Power granted
*Oct 23 19:14:21.664: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:14:21.771: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:14:22.215: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/19: PD removed
*Oct 23 19:14:22.216: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/19: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:22.418: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:14:23.023: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:14:23.673: %ILPOWER-7-DETECT: Interface Gi1/0/29: Power Device detected: Cisco PD
*Oct 23 19:14:26.222: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:14:26.352: %ILPOWER-7-DETECT: Interface Gi1/0/21: Power Device detected: Cisco PD
*Oct 23 19:14:26.938: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:14:28.256: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:14:28.591: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:14:28.653: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:14:29.277: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:14:29.277: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/28: Power granted
*Oct 23 19:14:30.038: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:14:30.040: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:14:30.158: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:14:30.353: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:14:30.714: %ILPOWER-7-DETECT: Interface Gi1/0/19: Power Device detected: Cisco PD
*Oct 23 19:14:31.227: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:14:31.394: %LINEPROTO-5-UPDOWN: Line protocol on Interface Capwap0, changed state to down
*Oct 23 19:14:31.408: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:14:32.102: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:14:33.104: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:14:35.282: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:14:36.098: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:14:38.322: %ILPOWER-7-DETECT: Interface Gi2/0/20: Power Device detected: Cisco PD
*Oct 23 19:14:38.662: %ILPOWER-7-DETECT: Interface Gi2/0/28: Power Device detected: Cisco PD
*Oct 23 19:14:38.734: %ILPOWER-7-DETECT: Interface Gi2/0/36: Power Device detected: Cisco PD
*Oct 23 19:14:39.211: %ILPOWER-5-POWER_GRANTED: Interface Gi2/0/20: Power granted
*Oct 23 19:14:39.673: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/29: PD removed
*Oct 23 19:14:39.674: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/29: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:39.742: %ILPOWER-7-DETECT: Interface Gi1/0/9: Power Device detected: Cisco PD
*Oct 23 19:14:40.149: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/20: PD removed
*Oct 23 19:14:40.151: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/28: PD removed
*Oct 23 19:14:40.195: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/36: PD removed
*Oct 23 19:14:41.063: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
*Oct 23 19:14:41.454: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: Cisco PD
*Oct 23 19:14:42.162: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted
*Oct 23 19:14:42.357: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/21: PD removed
*Oct 23 19:14:42.358: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/21: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:43.174: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed
*Oct 23 19:14:44.685: %ILPOWER-7-DETECT: Interface Gi2/0/34: Power Device detected: Cisco PD
*Oct 23 19:14:46.168: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi2/0/34: PD removed
*Oct 23 19:14:46.716: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/19: PD removed
*Oct 23 19:14:46.717: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/19: Power given, but State Machine Power Good wait timer timed out
*Oct 23 19:14:47.122: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination  
*Oct 23 19:14:47.122: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:47.122: *%LOG-3-Q_IND: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:47.122: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:14:47.123: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  58:f3:9c:3a:20:70  
*Oct 23 19:14:47.123: *%LWAPP-3-RD_ERR7: 1 wcm:  Invalid country code () for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:47.123: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP 58:f3:9c:3a:20:70  
*Oct 23 19:14:47.126: *%CAPWAP-3-POST_DECODE_ERR: 1 wcm:  Post decode processing failed for Config status from AP 58f3.9c3a.2070  
*Oct 23 19:14:47.132: %LINK-3-UPDOWN: Interface Capwap0, changed state to up

 

 

Everyone's tags (1)
2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

Hi Refer this post & make

Hi 

Refer this post & make sure you follow the correct steps

http://mrncciew.com/2013/09/29/getting-started-with-3850/

1. AP should be on the same vlan as wireless managment vlan configured
2. Correct country code configured on your 3850 for the AP
3. 3850 configured as Mobility Controller

This error msg indicating  a wrong regulartory domain AP (which mean country code may not correctly configured on your 3850)

Oct 23 19:13:46.102: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP 58:f3:9c:3a:20:70  

 

Let me know if all are correct & still you have issues

 

HTH

Rasika

**** Pls rate all useful responses ****

VIP Purple

HiThat's the mistake. You

Hi

That's the mistake. You have to configured the country as Vietnam as shown below

3850(config)#ap country VN

Things should work once you do this. Let me know if it is not the case :-)

Refer this for the identify correct regulatory domain. You have purchased the -E which is correct regulatory domain for Vietnam.

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1300-series/product_data_sheet0900aecd80537b6a.html

HTH

Rasika

**** Pls rate all useful responses ***

7 REPLIES
VIP Purple

Hi Refer this post & make

Hi 

Refer this post & make sure you follow the correct steps

http://mrncciew.com/2013/09/29/getting-started-with-3850/

1. AP should be on the same vlan as wireless managment vlan configured
2. Correct country code configured on your 3850 for the AP
3. 3850 configured as Mobility Controller

This error msg indicating  a wrong regulartory domain AP (which mean country code may not correctly configured on your 3850)

Oct 23 19:13:46.102: *%LWAPP-3-RD_ERR4: 1 wcm:  Invalid regulatory domain 802.11bg:-A     802.11a:-A for AP 58:f3:9c:3a:20:70  

 

Let me know if all are correct & still you have issues

 

HTH

Rasika

**** Pls rate all useful responses ****

New Member

Tks Rasika for your reply.I

Tks Rasika for your reply.

I followed that helpful site (mrncciew.com) to learn how to config WLAN on switch 3850.

All device (3850s and 3700) are located  in VietNam.

Some config on 3850:

vlan 99
 name WIFI_MNT

interface Vlan99
 ip address 10.9.9.1 255.255.255.0

ip dhcp pool WIFI_MNT
 network 10.9.9.0 255.255.255.0
 default-router 10.9.9.1 
 dns-server 10.9.9.1

interface GigabitEthernet2/0/21

 description *** Connect to AP013700 ***
 switchport access vlan 99
 switchport mode access
 spanning-tree portfast

wireless mobility controller
wireless management interface Vlan99
wlan ABCXYZ09 1 ABCXYZ09
 client vlan 300
 ip dhcp server 10.199.146.1
 no security wpa akm dot1x
 security wpa akm psk set-key ascii 0 ************
 wmm require
 shutdown
ap group default-group
end

 

 

I configured country code on 3850 to US:

MLVN-ACCESS-P1#sh wireless country configured 

 Configured Country.............................: US  - United States
 Configured Country Codes 
        US  - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

 

VIP Purple

HiThat's the mistake. You

Hi

That's the mistake. You have to configured the country as Vietnam as shown below

3850(config)#ap country VN

Things should work once you do this. Let me know if it is not the case :-)

Refer this for the identify correct regulatory domain. You have purchased the -E which is correct regulatory domain for Vietnam.

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1300-series/product_data_sheet0900aecd80537b6a.html

HTH

Rasika

**** Pls rate all useful responses ***

New Member

Dear Rasika,I configured to

Dear Rasika,

I configured to VN but maybe something wrong:

MLVN-ACCESS-P1(config)#ap country VN
Changing country code could reset channel and RRM grouping configuration. If running in RRM One-Time mode, reassign channels after this command. Check customized APs for valid channel values after this command. 
Are you sure you want to continue? (y/n)[y]: y
% switch-1:wcm:Disable 802.11a and 802.11b networks prior to configuring country code.
MLVN-ACCESS-P1(config)#sh con
MLVN-ACCESS-P1(config)#sh wire
MLVN-ACCESS-P1(config)#do sh wire
MLVN-ACCESS-P1(config)#do sh wireless co
MLVN-ACCESS-P1(config)#do sh wireless country co
MLVN-ACCESS-P1(config)#do sh wireless country configured 

 Configured Country.............................: US  - United States
 Configured Country Codes 
        US  - United States : 802.11a Indoor,Outdoor/ 802.11b / 802.11g

 

How can i disable Disable 802.11a and 802.11b networks ?
I do some search but no command like that in my 3850:

http://www.cisco.com/c/en/us/td/docs/wireless/controller/3-2/configuration/guide/ccfig32/c32ccfg.html#wp1082386

E

nEabling and Disabling 802.11 Bands

You can enable or disable the 802.11b/g (2.4-GHz) and the 802.11a (5-GHz) bands for the controller to comply with the regulatory requirements in your country. By default, both 802.11b/g and 802.11a are enabled.

On the CLI, enter config 80211b disable network to disable 802.11b/g operation on the controller. Enter config 80211b enable network to re-enable 802.11b/g operation.

Enter config 80211a disable network to disable 802.11a operation on the controller. Enter config 80211a enable network to re-enable 802.11a operation.

 

 

VIP Purple

Hi here is the full syntax

Hi 

here is the full syntax what you have to do. Let me know :)

3850(config)#ap dot11 5ghz shutdown 
3850(config)#ap dot11 24ghz shutdown 
3850(config)#ap country VN           
Changing country code could reset channel and RRM grouping configuration. If running in RRM One-Time mode, reassign channels after this command. Check customized APs for valid channel values after this command. 
Are you sure you want to continue? (y/n)[y]: y
3850(config)#no ap dot11 5ghz shutdown 
3850(config)#no ap dot11 24ghz shutdown 

 

HTH

Rasika

*** Pls rate all useful responses ****

New Member

 Dear Rasika,My problem is

 

Dear Rasika,

My problem is solved now. Very thank to your help!

Wish you success and happy!

VIP Purple

That great & glad I am able

That's great & glad I am able to help you today  :)

Give us a shout if you require any help in future.

Thanks for rating our responses as well

Rasika

1639
Views
15
Helpful
7
Replies
CreatePlease to create content