Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

need info about "sh int dot11Radio" and "sh int dot11Radio stati"

Hello,

Could someone explain me the counters in the 2 following display on an AP (like a AIR-AP1231G)

sh int dot11Radio 0

sh int dot11Radio 0 statistics

SiteR02#sh int dot11Radio 0

Dot11Radio0 is up, line protocol is up

Hardware is 802.11G Radio, address is 000f.3415.bf30 (bia 000f.3415.bf30)

MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:12, output 00:00:12, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/30 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

24680 packets input, 3282575 bytes, 0 no buffer

Received 129 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 input packets with dribble condition detected

23427 packets output, 4831674 bytes, 0 underruns

212 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

SiteR02#sh int dot11Radio 0 statistics

DOT11 Statistics (Cumulative Total/Last 5 Seconds):

RECEIVER TRANSMITTER

Host Rx Bytes: 3265473 / 0 Host Tx Bytes: 4338004 / 0

Unicasts Rx: 88699 / 1 Unicasts Tx: 27040 / 0

Unicasts to host: 88699 / 1 Unicasts by host: 23629 / 0

Broadcasts Rx: 0 / 0 Broadcasts Tx: 4601528 / 49

Beacons Rx: 0 / 0 Beacons Tx: 4601528 / 49

Broadcasts to host: 0 / 0 Broadcasts by host: 0 / 0

Multicasts Rx: 0 / 0 Multicasts Tx: 0 / 0

Multicasts to host: 0 / 0 Multicasts by host: 0 / 0

Mgmt Packets Rx: 0 / 0 Mgmt Packets Tx: 3411 / 0

RTS received: 0 / 0 RTS transmitted: 1721 / 0

Duplicate frames: 230 / 0 CTS not received: 1597 / 0

CRC errors: 4303 / 0 Unicast Fragments Tx: 26833 / 0

WEP errors: 0 / 0 Retries: 2540 / 0

Buffer full: 0 / 0 Packets one retry: 435 / 0

Host buffer full: 0 / 0 Packets > 1 retry: 174 / 0

Header CRC errors: 43265 / 0 Protocol defers: 2 / 0

Invalid header: 311 / 0 Energy detect defers: 206 / 0

Length invalid: 0 / 0 Jammer detected: 0 / 0

Incomplete fragments: 0 / 0 Packets aged: 0 / 0

Rx Concats: 0 / 0 Tx Concats: 0 / 0

RATE 2.0 Mbps

.....

RATE 5.5 Mbps

......

RATE 11.0 Mbps

........

SiteR02#

Somes counters are displayed on those 2 displays but it is not with the same figure (CRC errors, input, output, broadcast, ...)

Can someone explaines me this ?

regards,

2 REPLIES
Bronze

Re: need info about "sh int dot11Radio" and "sh int dot11Radio s

Show interface statistics shows number of error free packets whereas show interface statistics shows total number of packets.

New Member

Re: need info about "sh int dot11Radio" and "sh int dot11Radio s

Hello, do you know the formula ?

If I had errors to the "input field -from sh int-" then I don't get the unicats received field in the "sh int stat".

Regards,

635
Views
0
Helpful
2
Replies
CreatePlease to create content