Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

New Cisco Aironet 1602i isn't broadcasting the SSID I setup

New Cisco Aironet 1602i isn't broadcasting the SSID I setup

SSID I setup isn't broadcasting, so I can't see the wireless network to choose it and connect. On my laptop if I choose to specify the name of the SSID then I am able to connect to the wireless network. I only have 1 SSID setup on this AP. Does anyone know how to update the configuration so the SSID is broadcasted?

The green light on the AP is blinking on and off about 3 seconds; is this normal or should it stay lit all the time?

Current configuration : 1842 bytes

!

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname ap

!

!

logging rate-limit console 9

enable secret 5 $1$rrlE$msWqu8CGY/tpDkgRAAAIe/

!

no aaa new-model

no ip routing

no ip cef

!

!

!

dot11 syslog

!

dot11 ssid Mi Casa

   authentication open

   authentication key-management wpa version 2

   wpa-psk ascii 7 142017070F0C787B7579

!

!

crypto pki token default removal timeout 0

!

!

username Cisco privilege 15 password 7 112A1016141D

!

!

bridge irb

!

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm tkip

!

ssid Mi Casa

!

antenna gain 0

stbc

beamform ofdm

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio1

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm tkip

!

ssid Mi Casa

!

antenna gain 0

dfs band 3 block

stbc

beamform ofdm

channel dfs

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface GigabitEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

bridge-group 1

bridge-group 1 spanning-disabled

no bridge-group 1 source-learning

!

interface BVI1

ip address 192.168.10.200 255.255.255.0

no ip route-cache

!

ip default-gateway 192.168.10.1

ip forward-protocol nd

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

!

bridge 1 route ip

!

!

!

line con 0

line vty 0 4

login local

transport input all

!

end

1 ACCEPTED SOLUTION

Accepted Solutions

Re: New Cisco Aironet 1602i isn't broadcasting the SSID I setup

Hi you need to config guest mode on the ssid ... Read this bud

https://supportforums.cisco.com/docs/DOC-5442

Sent from Cisco Technical Support iPhone App

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________
1 REPLY

Re: New Cisco Aironet 1602i isn't broadcasting the SSID I setup

Hi you need to config guest mode on the ssid ... Read this bud

https://supportforums.cisco.com/docs/DOC-5442

Sent from Cisco Technical Support iPhone App

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________
2071
Views
0
Helpful
1
Replies
CreatePlease to create content