Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Not able to ping Cisco 2504 Mgmt IP / Urgent

Hi Team,

I am not able to ping Cisco WLC mgmt IP

Capture from WLC

(Cisco Controller) >show interface summary

Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Gu
est
-------------------------------- ---- -------- --------------- ------- ------ --
---
management                       1    663      10.210.126.133  Static  Yes    No

virtual                          N/A  N/A      1.1.1.1         Static  No     No

wifi-data                        1    662      10.210.126.3    Dynamic No     No

wifi-guest                       1    660      10.210.124.3    Dynamic No     No

                   

Capture from Switch ( switch side is having trunk port)

switch3#sh run int gigabitEthernet 4/13
Building configuration...

Current configuration : 370 bytes
!
interface GigabitEthernet4/13
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 660,662,663
switchport mode trunk
speed 100
duplex full

All the vlan having dhcp 660,662,663

Our L3 device is juniper NS 5200 firewall & From firewall I am not be able to ping the WLC IP

though I am learning the mac address in the firewall

fw3)-> get arp all | inc 10.210.126.

10.210.126.133  ece1a9548200   Wi-Fi-Vr/eth0/1.104    VLD    30      0       0     0 5FW2503(M)-> get arp all | inc 10.210.126.
10.210.126.133  ece1a9548200   Wi-Fi-Vr/eth0/1.104    VLD    30      0       0     0

Any quick help will be much appreciated as we have to go live

Br/Subhojit

8 REPLIES
Hall of Fame Super Silver

Re: Not able to ping Cisco 2504 Mgmt IP / Urgent

You have the correct gateway set on the management interface?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
VIP Purple

Re: Not able to ping Cisco 2504 Mgmt IP / Urgent

Noticed you have set speed 100 in switchport. WLC is expect to connect to Gigabit switch port & please remove that & try

HTH

Rasika

**** Pls rate all useful responses ****

New Member

Not able to ping Cisco 2504 Mgmt IP / Urgent

Hi

Problem resolved.

thanks...

VIP Purple

Not able to ping Cisco 2504 Mgmt IP / Urgent

what was the fix ?

New Member

Not able to ping Cisco 2504 Mgmt IP / Urgent

Hi,

Small query : How to change the AP side Lan port speed to 1 Gig/full duplex & Ap hostname ??

Over CLI / or Gui will be beneficial

VIP Purple

Not able to ping Cisco 2504 Mgmt IP / Urgent

AP name

"config ap name "

Duplex & Speed

(WLC2) >config ap ethernet duplex ?

Configure Ethernet Port Duplex Auto/Half/Full

(WLC2) >config ap ethernet duplex full ?

speed          Configure Ethernet Port Speed Settings

(WLC2) >config ap ethernet duplex full speed ?

Configure Ethernet Port Speed Auto/10Mbps/100Mbps/1000Mbps

(WLC2) >config ap ethernet duplex full speed 1000 ?

all            Configures Ethernet Port Setting for all connected APs

     Enter the name of the Cisco AP.

(WLC2) >config ap ethernet duplex full speed 1000

Normally you should not change these and leave it auto/auto.

HTH

Rasika

**** Pls rate all useful responses ****

Gold

Not able to ping Cisco 2504 Mgmt IP / Urgent

Hi Subhojit,

AP name can be changed through GUI (once AP get registered to WLC) or through AP console. On AP console you can use below command

capwap ap hostname 

AP speed and duplex can be changed through WLC CLI.

Below shows the commands for the same.

configure ap ethernet duplex speed

This command is supported with versions 4.1 and later only.

Hope that helps.

Regards

Najaf

Please rate when applicable or helpful !!!

Cisco Employee

Not able to ping Cisco 2504 Mgmt IP / Urgent

It seems to be some issue of Access-list configuration or the gateway configuration.

Could you please check that?

299
Views
5
Helpful
8
Replies
CreatePlease to create content