Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

The AP is connected to the WLC but keeps taking it's Raodio Down. As suggested I have played with the PoE settings to no avail.....


Wed Feb 1 18:30:36 2012
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
3Wed Feb 1 18:30:36 2012AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Enable
4Wed Feb 1 18:30:36 2012AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Disable
5Wed Feb 1 18:25:32 2012AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
6Wed Feb 1 18:25:29 2012AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio reset due to Init. Status:NA

Any Ideas... I have checked everything... AP is in Port 4 of the WLC

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Operational Status DOWN -WLC 2504 and LAP 3501

*Mar  1 00:00:12.988: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self                                 test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process=                                 "Init", ipl= 0, pid= 3 

Now this is what I'm looking for!

Your 802.11b radio is dead.  Please contact Cisco to get this WAP replaced.

32 REPLIES
Hall of Fame Super Silver

Re: Operational Status DOWN -WLC 2504 and LAP 3501

You really should not connect any ap to the 2504 ports. I believe that Cisco does not support that setup.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

I had heard that once before, but don't buy it as we have others running on the built in ports... just not 3501's.

Why would they put a 4 port PoE switch in and not support it?

Anyway - when I move to a separate PoE switch I get the same issue.

Hall of Fame Super Silver

Re: Operational Status DOWN -WLC 2504 and LAP 3501

The thing is you can if you want, but if you open a TAC case, they will tell you to put the ap on a switch.

When the ap is on the switch, is the port negotiating correctly? Do you see just the radio go down or the ap itself. Take a look at the ap uptime and join time.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

I am trying in another switch right now....

The AP is up and I can see it in the WLC. At first boot radio is up but then goes down.

Switch.

show inline power

Fa0/20    auto   on         15.0    AIR-CAP3501I-A-K9   3     15.4 

sh int fa0/20

Full-duplex, 100Mb/s,

Hall of Fame Super Silver

Re: Operational Status DOWN -WLC 2504 and LAP 3501

Do you have an SSID configured and enabled?

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Yes - I have created two... One with my standard security parameters and one - open, no security- just to see if that was the issue..

Hall of Fame Super Silver

Re: Operational Status DOWN -WLC 2504 and LAP 3501

Okay... Well is it an issue with one ap or do you have other AP's that are working. Can you post your show run-config.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Only have one LAP at the moment... The plan was once I got it working I would "upgrade" my AP's to LAP.

(Cisco Controller) show>run-config

Press Enter to continue...

System Inventory

NAME: "Chassis"    , DESCR: "Cisco 2500 Series Wireless LAN Controller"

PID: AIR-CT2504-K9,  VID: V01,  SN: PSJ154208DT

Burned-in MAC Address............................ D0:C2:82:E1:DA:A0

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.116.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 1.0.0

Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... Cisco_e1:da:a4

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1279

IP Address....................................... 10.161.98.20

Last Reset....................................... Software reset

System Up Time................................... 0 days 3 hrs 20 mins 48 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

--More or (q)uit current module or to abort

Next Boot License Type........................... Permanent

Configured Country............................... CA  - Canada

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +20 C

External Temperature............................. +24 C

Fan Status....................................... 4200 rpm

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 2

Number of Active Clients......................... 0

Burned-in MAC Address............................ D0:C2:82:E1:DA:A0

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

                                                         Strong Password Check

eatures:

         case-check ...........Enabled

         consecutive-check ....Enabled

         default-check .......Enabled

         username-check ......Enabled

Press Enter to continue or to abort

Network Information

RF-Network Name............................. e2e

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

Secure Shell (ssh).......................... Enable

Telnet...................................... Enable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Multicast   Address : 0.0.0.0

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

IGMP Query Interval......................... 20 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Enabled

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

Bridge MAC filter Config.................... Enable

Bridge Security Mode........................ EAP

--More or (q)uit current module or to abort

Mesh Full Sector DFS........................ Enable

AP Fallback ................................ Enable

Web Auth Redirect Ports .................... 80

Web Auth Proxy Redirect  ................... Disable

Fast SSID Change ........................... Disabled

IP/MAC Addr Binding Check .................. Enabled

Press Enter to continue or to abort

Port Summary

           STP   Admin   Physical   Physical   Link   Link

Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE

-- ------- ---- ------- ---------- ---------- ------ ------- -------

1  Normal  Forw Enable  Auto       100 Full   Up     Enable  N/A

2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A

3  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off

4  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off

Press Enter to continue or to abort

AP Summary

Number of APs.................................... 1

Global AP User Name.............................. Not Configured

Global AP Dot1x User Name........................ Not Configured

AP Name             Slots  AP Model              Ethernet MAC       Location

      Port  Country  Priority

------------------  -----  --------------------  -----------------  -----------

----  ----  -------  ------

APe8b7.48ac.1050     1     AIR-CAP3501I-A-K9     e8:b7:48:ac:10:50  default loc

tion  1        CA       1

AP Tcp-Mss-Adjust Info

AP Name              TCP State  MSS Size

------------------   --------   -------

APe8b7.48ac.1050     disabled   -

Press Enter to continue or to abort

AP Location

Total Number of AP Groups........................ 1

Site Name........................................ default-group

Site Description.................................

WLAN ID          Interface          Network Admission Control          Radio Po

icy

-------          -----------        --------------------------         --------

---

1               management           Disabled                          None

2               management           Disabled                          None

AP Name             Slots  AP Model             Ethernet MAC       Location

     Port  Country  Priority

------------------  -----  -------------------  -----------------  ------------

---  ----  -------  --------

APe8b7.48ac.1050     1     AIR-CAP3501I-A-K9    e8:b7:48:ac:10:50  default loca

ion  1     CA       1

Press Enter to continue or to abort

AP Config

Cisco AP Identifier.............................. 1

Cisco AP Name.................................... APe8b7.48ac.1050

Country code..................................... CA  - Canada

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. CA  - Canada

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... e8:b7:48:ac:10:50

IP Address Configuration......................... Static IP assigned

IP Address....................................... 10.161.98.108

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 10.161.98.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

--More or (q)uit current module or to abort

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.116.0

Boot  Version ................................... 12.4.23.0

Mini IOS Version ................................ 7.0.112.74

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 1

--More or (q)uit current module or to abort

AP Model......................................... AIR-CAP3501I-A-K9

AP Image......................................... C3500-K9W8-M

IOS Version...................................... 12.4(23c)JA2

Reset Button..................................... Enabled

AP Serial Number................................. FTX1523E3L1

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 36 m 02 s

AP LWAPP Up Time................................. 0 days, 00 h 34 m 58 s

Join Date and Time............................... Wed Feb  1 19:55:09 2012

Join Taken Time.................................. 0 days, 00 h 01 m 03 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. DOWN

    Radio Role .................................. ACCESS

    CellId ...................................... 0

--More or (q)uit current module or to abort

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 2

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... e8:ba:70:93:81:60

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

--More or (q)uit current module or to abort

        MCS 1.................................... SUPPORTED

        MCS 2.................................... SUPPORTED

        MCS 3.................................... SUPPORTED

        MCS 4.................................... SUPPORTED

        MCS 5.................................... SUPPORTED

        MCS 6.................................... SUPPORTED

        MCS 7.................................... SUPPORTED

        MCS 8.................................... SUPPORTED

        MCS 9.................................... SUPPORTED

        MCS 10................................... SUPPORTED

        MCS 11................................... SUPPORTED

        MCS 12................................... SUPPORTED

        MCS 13................................... SUPPORTED

        MCS 14................................... SUPPORTED

        MCS 15................................... SUPPORTED

      Beacon Period ............................. 100

      Fragmentation Threshold ................... 2346

      Multi Domain Capability Implemented ....... TRUE

      Multi Domain Capability Enabled ........... TRUE

      Country String ............................ CA

    Multi Domain Capability

      Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

      First Chan Num ............................ 1

      Number Of Channels ........................ 11

    MAC Operation Parameters

      Configuration ............................. AUTOMATIC

      Fragmentation Threshold ................... 2346

      Packet Retry Limit ........................ 64

    Tx Power

      Num Of Supported Power Levels ............. 8

      Tx Power Level 1 .......................... 20 dBm

      Tx Power Level 2 .......................... 17 dBm

      Tx Power Level 3 .......................... 14 dBm

      Tx Power Level 4 .......................... 11 dBm

      Tx Power Level 5 .......................... 8 dBm

      Tx Power Level 6 .......................... 5 dBm

      Tx Power Level 7 .......................... 2 dBm

      Tx Power Level 8 .......................... -1 dBm

      Tx Power Configuration .................... AUTOMATIC

      Current Tx Power Level .................... 1

    Phy OFDM parameters

      Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

      Current Channel ........................... 1

      Extension Channel ......................... NONE

      Channel Width.............................. 20 Mhz

      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

      TI Threshold .............................. -50

      Legacy Tx Beamforming Configuration ....... AUTOMATIC

      Legacy Tx Beamforming ..................... DISABLED

      Antenna Type............................... INTERNAL_ANTENNA

      Internal Antenna Gain (in .5 dBi units).... 8

      Diversity.................................. DIVERSITY_ENABLED

      802.11n Antennas

         A....................................... ENABLED

         B....................................... ENABLED

         C....................................... ENABLED

    Performance Profile Parameters

      Configuration ............................. AUTOMATIC

      Interference threshold..................... 10 %

      Noise threshold............................  -70 dBm

      RF utilization threshold................... 80 %

      Data-rate threshold........................ 1000000 bps

      Client threshold........................... 12 clients

      Coverage SNR threshold..................... 12 dB

--More or (q)uit current module or to abort

      Coverage exception level................... 25 %

      Client minimum exception level............. 3 clients

    Rogue Containment Information

    Containment Count............................ 0

    CleanAir Management Information

        CleanAir Capable......................... Yes

        CleanAir Management Admin State.......... Disabled

        CleanAir Management Operation State...... Down

        Rapid Update Mode........................ Off

        Spectrum Expert connection............... Enabled

          CleanAir NSI Key....................... F5E484D89473C69EF67D707E24008

B0

         Spectrum Expert Connections counter..... 0

        CleanAir Sensor State.................... Radio is disabled. Turn ON ra

io to enable CleanAir functionality

AP does not have the 802.11a radio.

Press Enter to continue or to abort

Press Enter to continue or to abort

AP Airewave Director Configuration

Number Of Slots.................................. 1

AP Name.......................................... APe8b7.48ac.1050

MAC Address...................................... e8:b7:48:ac:10:50

  Slot ID........................................ 0

  Radio Type..................................... RADIO_TYPE_80211b/g

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 0 %

    Channel Utilization.......................... 0 %

    Attached Clients............................. 0 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

--More or (q)uit current module or to abort

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

  Radar Information

  Channel Assignment Information

    Current Channel Average Energy............... unknown

    Previous Channel Average Energy.............. unknown

    Channel Change Count......................... 0

--More or (q)uit current module or to abort

    Last Channel Change Time..................... Wed Feb  1 19:55:08 2012

    Recommended Best Channel..................... 1

  RF Parameter Recommendations

    Power Level.................................. 1

    RTS/CTS Threshold............................ 2347

    Fragmentation Threshold...................... 2346

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ---------------------

--

  All third party trademarks are the property of their respective owners.

AP does not have the 802.11a radio.

Press Enter to continue or to abort

Press Enter to continue or to abort

802.11a Configuration

802.11a Network.................................. Disabled

11nSupport....................................... Enabled

      802.11a Low Band........................... Enabled

      802.11a Mid Band........................... Enabled

      802.11a High Band.......................... Enabled

802.11a Operational Rates

    802.11a 6M Rate.............................. Mandatory

    802.11a 9M Rate.............................. Supported

    802.11a 12M Rate............................. Mandatory

    802.11a 18M Rate............................. Supported

    802.11a 24M Rate............................. Mandatory

    802.11a 36M Rate............................. Supported

    802.11a 48M Rate............................. Supported

    802.11a 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

    MCS 5........................................ Supported

    MCS 6........................................ Supported

--More or (q)uit current module or to abort

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    A-MSDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Enabled

        Priority 2............................... Enabled

--More or (q)uit current module or to abort

        Priority 3............................... Enabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    Rifs Rx ..................................... Enabled

    Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mandatory............................ Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 36

Default Tx Power Level........................... 0

DTPC  Status..................................... Disabled

Fragmentation Threshold.......................... 2346

TI Threshold..................................... -50

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

--More or (q)uit current module or to abort

Call Admission Control (CAC) configuration

Voice AC:

   Voice AC - Admission control (ACM)............ Disabled

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice CAC Method ............................. Load-Based

   Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

   SIP based CAC ................................ Disabled

   SIP Codec Type ............................... CODEC_TYPE_G711

   SIP call bandwidth ........................... 64

   SIP call bandwith sample-size ................ 20

Video AC:

   Video AC - Admission control (ACM)............ Disabled

   Video max RF bandwidth........................ Infinite

   Video reserved roaming bandwidth.............. 0

   Best-effort AC - Admission control (ACM)...... Disabled

   Background AC - Admission control (ACM)....... Disabled

Press Enter to continue or to abort

802.11a Advanced Configuration

AP Name                          MAC Address        Admin State  Operation Stat

Channel    TxPower

-------------------------------- ------------------ ------------ --------------

---------- --------

Press Enter to continue or to abort

802.11a Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  TxPower Update Logging......................... Off

Default 802.11a AP performance profiles

  802.11a Global Interference threshold.......... 10 %

  802.11a Global noise threshold................. -70 dBm

  802.11a Global RF utilization threshold........ 80 %

  802.11a Global throughput threshold............ 1000000 bps

  802.11a Global clients threshold............... 12 clients

Default 802.11a AP monitoring

  802.11a Monitor Mode........................... enable

  802.11a Monitor Mode for Mesh AP Backhaul...... disable

  802.11a Monitor Channels....................... Country channels

  802.11a RRM Neighbor Discover Type............. Transparent

  802.11a AP Coverage Interval................... 180 seconds

  802.11a AP Load Interval....................... 60 seconds

--More or (q)uit current module or to abort

  802.11a AP Noise Interval...................... 180 seconds

  802.11a AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI..

  Transmit Power Assignment Leader............... Cisco_e1:da:a4 (10.161.98.20)

  Last Run....................................... 13 seconds ago

Coverage Hole Detection

  802.11a Coverage Hole Detection Mode........... Enabled

  802.11a Coverage Voice Packet Count............ 100 packets

  802.11a Coverage Voice Packet Percentage....... 50%

  802.11a Coverage Voice RSSI Threshold.......... -80 dBm

  802.11a Coverage Data Packet Count............. 50 packets

  802.11a Coverage Data Packet Percentage........ 50%

  802.11a Coverage Data RSSI Threshold........... -80 dBm

  802.11a Global coverage exception level........ 25 %

  802.11a Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

--More or (q)uit current module or to abort

  Channel Assignment Mode........................ AUTO

  Channel Update Interval........................ 600 seconds

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI..

  CleanAir Event-driven RRM option............... Disabled

  CleanAir Event-driven RRM sensitivity.......... Medium

  Channel Assignment Leader...................... Cisco_e1:da:a4 (10.161.98.20)

  Last Run....................................... 13 seconds ago

  DCA Sensitivity Level.......................... MEDIUM (15 dB)

  DCA 802.11n Channel Width...................... 20 MHz

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  802.11a 5 GHz Auto-RF Channel List

    Allowed Channel List......................... 36,40,44,48,52,56,60,64,149,

                                                  153,157,161

    Unused Channel List.......................... 100,104,108,112,116,132,136,

--More or (q)uit current module or to abort

                                                  140,165

  802.11a 4.9 GHz Auto-RF Channel List

    Allowed Channel List.........................

    Unused Channel List.......................... 1,2,3,4,5,6,7,8,9,10,11,12,

                                                  13,14,15,16,17,18,19,20,21,

                                                  22,23,24,25,26

  DCA Outdoor AP option.......................... Disabled

Radio RF Grouping

  802.11a Group Mode............................. AUTO

  802.11a Group Update Interval.................. 600 seconds

  802.11a Group Leader........................... Cisco_e1:da:a4 (10.161.98.20)

    802.11a Group Member......................... Cisco_e1:da:a4 (10.161.98.20)

  802.11a Last Run............................... 13 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Disabled

Air Quality Settings:

    Air Quality Reporting........................ Enabled

    Air Quality Reporting Period (min)........... 15

    Air Quality Alarms........................... Enabled

    Air Quality Alarm Threshold.................. 35

Interference Device Settings:

    Interference Device Reporting................ Enabled

--More or (q)uit current module or to abort

    Interference Device Types:

        TDD Transmitter.......................... Enabled

        Jammer................................... Enabled

        Continuous Transmitter................... Enabled

        DECT-like Phone.......................... Enabled

        Video Camera............................. Enabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Enabled

        Canopy................................... Enabled

        WiMax Mobile............................. Enabled

        WiMax Fixed.............................. Enabled

    Interference Device Alarms................... Enabled

    Interference Device Types Triggering Alarms:

        TDD Transmitter.......................... Disabled

        Jammer................................... Enabled

        Continuous Transmitter................... Disabled

        DECT-like Phone.......................... Disabled

        Video Camera............................. Disabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Disabled

        Canopy................................... Disabled

--More or (q)uit current module or to abort

        WiMax Mobile............................. Disabled

        WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

    CleanAir Event-driven RRM State.............. Disabled

    CleanAir Driven RRM Sensitivity.............. Medium

    CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

                 DFS = Dynamic Frequency Selection

AP Name            Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

Press Enter to continue or to abort

802.11b Configuration

802.11b Network.................................. Enabled

11gSupport....................................... Enabled

11nSupport....................................... Enabled

802.11b/g Operational Rates

    802.11b/g 1M Rate............................ Mandatory

    802.11b/g 2M Rate............................ Mandatory

    802.11b/g 5.5M Rate.......................... Mandatory

    802.11b/g 11M Rate........................... Mandatory

    802.11g 6M Rate.............................. Supported

    802.11g 9M Rate.............................. Supported

    802.11g 12M Rate............................. Supported

    802.11g 18M Rate............................. Supported

    802.11g 24M Rate............................. Supported

    802.11g 36M Rate............................. Supported

    802.11g 48M Rate............................. Supported

    802.11g 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

--More or (q)uit current module or to abort

    MCS 5........................................ Supported

    MCS 6........................................ Supported

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    A-MSDU Tx:

        Priority 0............................... Enabled

--More or (q)uit current module or to abort

        Priority 1............................... Enabled

        Priority 2............................... Enabled

        Priority 3............................... Enabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    Rifs Rx ..................................... Enabled

    Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mode................................. Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 1

Default Tx Power Level........................... 0

DTPC  Status..................................... Enabled

Call Admission Limit  ........................... 105

G711 CU Quantum ................................. 15

ED Threshold..................................... -50

Fragmentation Threshold.......................... 2346

PBCC mandatory................................... Disabled

RTS Threshold.................................... 2347

--More or (q)uit current module or to abort

Short Preamble mandatory......................... Enabled

Short Retry Limit................................ 7

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

Faster Carrier Tracking Loop..................... Disabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admission Control (CAC) configuration

   Voice AC - Admission control (ACM)............ Disabled

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice CAC Method.............................. Load-Based

   Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

   SIP based CAC ................................ Disabled

   SIP Codec Type ............................... CODEC_TYPE_G711

   SIP call bandwidth: .......................... 64

   SIP call bandwidth sample-size ............... 20

   Video AC - Admission control (ACM)............ Disabled

--More or (q)uit current module or to abort

   Video max RF bandwidth........................ Infinite

   Video reserved roaming bandwidth.............. 0

   Best-effort AC - Admission control (ACM)...... Disabled

   Background AC - Admission control (ACM)....... Disabled

Press Enter to continue or to abort

802.11b Advanced Configuration

AP Name                          MAC Address        Admin State  Operation Stat

Channel    TxPower

-------------------------------- ------------------ ------------ --------------

---------- --------

APe8b7.48ac.1050                 e8:ba:70:93:81:60  ENABLED      DOWN

1*           1(*)

Press Enter to continue or to abort

802.11b Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  Transmit Power Update Logging.................. Off

Default 802.11b AP performance profiles

  802.11b Global Interference threshold.......... 10 %

  802.11b Global noise threshold................. -70 dBm

  802.11b Global RF utilization threshold........ 80 %

  802.11b Global throughput threshold............ 1000000 bps

  802.11b Global clients threshold............... 12 clients

Default 802.11b AP monitoring

  802.11b Monitor Mode........................... enable

  802.11b Monitor Channels....................... Country channels

  802.11b RRM Neighbor Discovery Type............ Transparent

  802.11b AP Coverage Interval................... 180 seconds

  802.11b AP Load Interval....................... 60 seconds

  802.11b AP Noise Interval...................... 180 seconds

--More or (q)uit current module or to abort

  802.11b AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI..

  Transmit Power Assignment Leader............... Cisco_e1:da:a4 (10.161.98.20)

  Last Run....................................... 14 seconds ago

Coverage Hole Detection

  802.11b Coverage Hole Detection Mode........... Enabled

  802.11b Coverage Voice Packet Count............ 100 packets

  802.11b Coverage Voice Packet Percentage....... 50%

  802.11b Coverage Voice RSSI Threshold.......... -80 dBm

  802.11b Coverage Data Packet Count............. 50 packets

  802.11b Coverage Data Packet Percentage........ 50%

  802.11b Coverage Data RSSI Threshold........... -80 dBm

  802.11b Global coverage exception level........ 25 %

  802.11b Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

  Channel Assignment Mode........................ AUTO

--More or (q)uit current module or to abort

  Channel Update Interval........................ 600 seconds

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI..

  CleanAir Event-driven RRM option............... Disabled

  CleanAir Event-driven RRM sensitivity.......... Medium

  Channel Assignment Leader...................... Cisco_e1:da:a4 (10.161.98.20)

  Last Run....................................... 14 seconds ago

  DCA Sensitivity Level: ...................... MEDIUM (10 dB)

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  802.11b Auto-RF Allowed Channel List........... 1,6,11

  Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10

Radio RF Grouping

  802.11b Group Mode............................. AUTO

  802.11b Group Update Interval.................. 600 seconds

--More or (q)uit current module or to abort

  802.11b Group Leader........................... Cisco_e1:da:a4 (10.161.98.20)

    802.11b Group Member......................... Cisco_e1:da:a4 (10.161.98.20)

  802.11b Last Run............................... 14 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Enabled

Air Quality Settings:

    Air Quality Reporting........................ Enabled

    Air Quality Reporting Period (min)........... 15

    Air Quality Alarms........................... Enabled

    Air Quality Alarm Threshold.................. 35

Interference Device Settings:

    Interference Device Reporting................ Enabled

    Interference Device Types:

        Bluetooth Link........................... Enabled

        Microwave Oven........................... Enabled

        802.11 FH................................ Enabled

        Bluetooth Discovery...................... Enabled

        TDD Transmitter.......................... Enabled

        Jammer................................... Enabled

        Continuous Transmitter................... Enabled

        DECT-like Phone.......................... Enabled

        Video Camera............................. Enabled

--More or (q)uit current module or to abort

        802.15.4................................. Enabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Enabled

        Canopy................................... Enabled

        Microsoft Device......................... Enabled

        WiMax Mobile............................. Enabled

        WiMax Fixed.............................. Enabled

    Interference Device Alarms................... Enabled

    Interference Device Types Triggering Alarms:

        Bluetooth Link........................... Disabled

        Microwave Oven........................... Disabled

        802.11 FH................................ Disabled

        Bluetooth Discovery...................... Disabled

        TDD Transmitter.......................... Disabled

        Jammer................................... Enabled

        Continuous Transmitter................... Disabled

        DECT-like Phone.......................... Disabled

        Video Camera............................. Disabled

        802.15.4................................. Disabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Disabled

--More or (q)uit current module or to abort

        Canopy................................... Disabled

        Microsoft Device......................... Disabled

        WiMax Mobile............................. Disabled

        WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

    CleanAir Event-driven RRM State.............. Disabled

    CleanAir Driven RRM Sensitivity.............. Medium

    CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

                 DFS = Dynamic Frequency Selection

AP Name            Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

Press Enter to continue or to abort

Mobility Configuration

Symmetric Mobility Tunneling (current) .......... Enabled

Symmetric Mobility Tunneling (after reboot) ..... Enabled

Mobility Protocol Port........................... 16666

Default Mobility Domain.......................... e2e

Multicast Mode .................................. Disabled

Mobility Domain ID for 802.11r................... 0x937a

Mobility Keepalive Interval...................... 10

Mobility Keepalive Count......................... 3

Mobility Group Members Configured................ 1

Mobility Control Message DSCP Value.............. 0

Controllers configured in the Mobility Group

MAC Address        IP Address       Group Name                        Multicas

IP     Status

d0:c2:82:e1:da:a0  10.161.98.20     e2e                               0.0.0.0

        Up

Press Enter to continue or to abort

Mobility Foreign Map Configuration

WLAN ID     Foreign Mac Address     Interface

-------     -------------------     ---------

Press Enter to continue or to abort

Advanced Configuration

Probe request filtering..........................  Enabled

Probes fwd to controller per client per radio....  2

Probe request rate-limiting interval.............  500 msec

Aggregate Probe request interval.................  500 msec

EAP-Identity-Request Timeout (seconds)........... 30

EAP-Identity-Request Max Retries................. 2

EAP Key-Index for Dynamic WEP.................... 0

EAP Max-Login Ignore Identity Response........... enable

EAP-Request Timeout (seconds).................... 30

EAP-Request Max Retries.......................... 2

EAPOL-Key Timeout (milliseconds)................. 1000

EAPOL-Key Max Retries............................ 2

EAP-Broadcast Key Interval....................... 3600

dot11-padding.................................... Disabled

Press Enter to continue or to abort

Location Configuration

RFID Tag data Collection......................... Enabled

RFID  timeout.................................... 1200 seconds

RFID mobility.................................... Oui:00:14:7e : Vendor:pango

tate:Disabled

Press Enter to continue or to abort

Interface Configuration

Interface Name................................... management

MAC Address...................................... d0:c2:82:e1:da:a0

IP Address....................................... 10.161.98.20

IP Netmask....................................... 255.255.255.0

IP Gateway....................................... 10.161.98.1

External NAT IP State............................ Disabled

External NAT IP Address.......................... 0.0.0.0

VLAN............................................. untagged

Quarantine-vlan.................................. 0

Active Physical Port............................. 1

Primary Physical Port............................ 1

Backup Physical Port............................. Unconfigured

Primary DHCP Server.............................. 10.161.98.20

Secondary DHCP Server............................ Unconfigured

DHCP Option 82................................... Disabled

ACL.............................................. Unconfigured

AP Manager....................................... Yes

Guest Interface.................................. No

L2 Multicast..................................... Disabled

Interface Name................................... virtual

MAC Address...................................... d0:c2:82:e1:da:a0

IP Address....................................... 1.1.1.1

DHCP Option 82................................... Disabled

Virtual DNS Host Name............................ Disabled

AP Manager....................................... No

Guest Interface.................................. No

Press Enter to continue or to abort

Interface Group Configuration

Press Enter to continue or to abort

WLAN Configuration

WLAN Identifier.................................. 1

Profile Name..................................... E2E

Network Name (SSID).............................. e2e50

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

  Radius-NAC State............................... Disabled

  SNMP-NAC State................................. Disabled

  Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 0

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

Multicast Interface.............................. Not Configured

--More or (q)uit current module or to abort

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

Static IP client tunneling....................... Disabled

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 4,5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

WMM UAPSD Compliant Client Support............... Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Passive Client Feature........................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

   Authentication................................ 10.161.96.50 1812

--More or (q)uit current module or to abort

   Accounting.................................... Global Servers

   Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

   802.11 Authentication:........................ Open System

   Static WEP Keys............................... Disabled

   802.1X........................................ Disabled

   Wi-Fi Protected Access (WPA/WPA2)............. Enabled

      WPA (SSN IE)............................... Disabled

      WPA2 (RSN IE).............................. Enabled

         TKIP Cipher............................. Disabled

         AES Cipher.............................. Enabled

                                                               Auth Key Managem

nt

         802.1x.................................. Enabled

         PSK..................................... Disabled

         CCKM.................................... Disabled

         FT(802.11r)............................. Disabled

         FT-PSK(802.11r)......................... Disabled

FT Reassociation Timeout......................... 20

FT Over-The-Air mode............................. Enabled

FT Over-The-Ds mode.............................. Enabled

CCKM tsf Tolerance............................... 1000

--More or (q)uit current module or to abort

   CKIP ......................................... Disabled

   Web Based Authentication...................... Disabled

   Web-Passthrough............................... Disabled

   Conditional Web Redirect...................... Disabled

   Splash-Page Web Redirect...................... Disabled

   Auto Anchor................................... Disabled

   H-REAP Local Switching........................ Disabled

   H-REAP Local Authentication................... Disabled

   H-REAP Learn IP Address....................... Enabled

   Client MFP.................................... Optional

   Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Roamed Call Re-Anchor Policy..................... Disabled

SIP CAC Fail Send-486-Busy Policy................ Enabled

SIP CAC Fail Send Dis-Association Policy......... Disabled

Band Select...................................... Disabled

Load Balancing................................... Disabled

Mobility Anchor List

WLAN ID     IP Address            Status

-------     ---------------       ------

Press Enter to continue or to abort

WLAN Configuration

WLAN Identifier.................................. 2

Profile Name..................................... TESTING

Network Name (SSID).............................. TESTING

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

  Radius-NAC State............................... Disabled

  SNMP-NAC State................................. Disabled

  Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 0

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

Multicast Interface.............................. Not Configured

--More or (q)uit current module or to abort

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

Static IP client tunneling....................... Disabled

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 4,5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

WMM UAPSD Compliant Client Support............... Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Passive Client Feature........................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

   Authentication................................ Global Servers

--More or (q)uit current module or to abort

   Accounting.................................... Global Servers

   Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

   802.11 Authentication:........................ Open System

   Static WEP Keys............................... Disabled

   802.1X........................................ Disabled

   Wi-Fi Protected Access (WPA/WPA2)............. Disabled

   CKIP ......................................... Disabled

   Web Based Authentication...................... Disabled

   Web-Passthrough............................... Disabled

   Conditional Web Redirect...................... Disabled

   Splash-Page Web Redirect...................... Disabled

   Auto Anchor................................... Disabled

   H-REAP Local Switching........................ Disabled

   H-REAP Local Authentication................... Disabled

   H-REAP Learn IP Address....................... Enabled

   Client MFP.................................... Optional but inactive (WPA2 n

t configured)

   Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Roamed Call Re-Anchor Policy..................... Disabled

SIP CAC Fail Send-486-Busy Policy................ Enabled

--More or (q)uit current module or to abort

SIP CAC Fail Send Dis-Association Policy......... Disabled

Band Select...................................... Disabled

Load Balancing................................... Disabled

Mobility Anchor List

WLAN ID     IP Address            Status

-------     ---------------       ------

Press Enter to continue or to abort

Press Enter to continue or to abort

ACL Configuration

Press Enter to continue or to abort

CPU ACL Configuration

CPU Acl Name................................ NOT CONFIGURED

Wireless Traffic............................ Disabled

Wired Traffic............................... Disabled

Press Enter to continue or to abort

RADIUS Configuration

Vendor Id Backward Compatibility................. Disabled

Call Station Id Case............................. lower

Call Station Id Type............................. IP Address

Aggressive Failover.............................. Enabled

Keywrap.......................................... Disabled

Fallback Test:

    Test Mode.................................... Off

    Probe User Name.............................. cisco-probe

    Interval (in seconds)........................ 300

MAC Delimiter for Authentication Messages........ hyphen

MAC Delimiter for Accounting Messages............ hyphen

Authentication Servers

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/

hase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  -----------------

------------------------------

1    NM    10.161.96.50      1812    Enabled   2     Enabled   Disabled - none/

nknown/group-0/0 none/none

2    NM    10.161.96.98      1812    Enabled   2     Enabled   Disabled - none/

nknown/group-0/0 none/none

Accounting Servers

--More or (q)uit current module or to abort

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/

hase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  -----------------

------------------------------

Press Enter to continue or to abort

TACACS Configuration

Authentication Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Authorization Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Accounting Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Press Enter to continue or to abort

LDAP Configuration

Press Enter to continue or to abort

Local EAP Configuration

User credentials database search order:

    Primary ..................................... Local DB

Timer:

    Active timeout .............................. 300

Configured EAP profiles:

EAP Method configuration:

    EAP-FAST:

      Server key ................................

      TTL for the PAC ........................... 10

      Anonymous provision allowed ............... Yes

      Authority ID .............................. 436973636f0000000000000000000

00

      Authority Information ..................... Cisco A-ID

Press Enter to continue or to abort

HREAP Group Summary

HREAP Group Summary: Count: 0

Group Name                # Aps

Press Enter to continue or to abort

HREAP Group Detail

Press Enter to continue or to abort

Route  Info

Number of Routes................................. 0

Destination Network          Netmask               Gateway

-------------------    -------------------   -------------------

Press Enter to continue or to abort

Qos Queue Length Info

Platinum queue length............................ 100

Gold queue length................................  75

Silver queue length..............................  50

Bronze queue length..............................  25

Press Enter to continue or to abort

Mac Filter Info

Press Enter to continue or to abort

Authorization List

Authorize MIC APs against AAA ................... disabled

Authorize LSC APs against Auth-List ............. disabled

APs Allowed to Join

  AP with Manufacturing Installed Certificate.... yes

  AP with Self-Signed Certificate................ no

  AP with Locally Significant Certificate........ no

Press Enter to continue or to abort

Load Balancing Info

Aggressive Load Balancing........................ per WLAN enabling

Aggressive Load Balancing Window................. 5 clients

Aggressive Load Balancing Denial Count........... 3

                                                    Statistics

Total Denied Count............................... 0 clients

Total Denial Sent................................ 0 messages

Exceeded Denial Max Limit Count.................. 0 times

None 5G Candidate Count.......................... 0 times

None 2.4G Candidate Count........................ 0 times

Press Enter to continue or to abort

DHCP Info

No leases allocated.

DHCP Opt-82 RID Format:

DHCP Proxy Behaviour:   disabled

Press Enter to continue or to abort

Exclusion List ConfigurationUnable to retrieve exclusion-list entry

Press Enter to continue or to abort

CDP Configuration

cdp version v2

Press Enter to continue or to abort

Country Channels Configuration

Configured Country............................. CA  - Canada

      KEY: * = Channel is legal in this country and may be configured manually.

           A = Channel is the Auto-RF default in this country.

           . = Channel is not legal in this country.

           C = Channel has been configured for use by Auto-RF.

           x = Channel is available to be configured for use by Auto-RF.

         (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11bg     :

    Channels     :                   1 1 1 1 1

                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A   ,-ABN ): A * * * * A * * * * A . . .

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

    Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6

                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A   ,-ABN ): . A . A . A . A A A A A * * * * * . . . * * * A A A A *

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

--More or (q)uit current module or to abort

4.9GHz 802.11a  :

    Channels     :                   1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2

                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A   ,-ABN ): * * * * * * * * * * * * * * * * * * * A * * * * * A

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

Press Enter to continue or to abort

WPS Configuration Summary

Auto-Immune

  Auto-Immune.................................... Disabled

Client Exclusion Policy

  Excessive 802.11-association failures.......... Enabled

  Excessive 802.11-authentication failures....... Enabled

  Excessive 802.1x-authentication................ Enabled

  IP-theft....................................... Enabled

  Excessive Web authentication failure........... Enabled

Signature Policy

  Signature Processing........................... Enabled

Press Enter to continue or to abort

Custom Web Configuration

Radius Authentication Method..................... PAP

Cisco Logo....................................... Enabled

CustomLogo....................................... None

Custom Title..................................... None

Custom Message................................... None

Custom Redirect URL.............................. None

Web Authentication Type.......................... Internal Default

External Web Authentication URL.................. None

Configuration Per Profile:

Press Enter to continue or to abort

Core dump Configuration

Core Dump is disabled

Press Enter to continue or to abort

Rogue AP Configuration

Rogue on wire Auto-Contain....................... Disabled

Rogue using our SSID Auto-Contain................ Disabled

Valid client on rogue AP Auto-Contain............ Disabled

Rogue AP timeout................................. 1200

Monitor Mode Report Interval..................... 10

MAC Address        Classification     # APs # Clients Last Heard

-----------------  ------------------ ----- --------- -----------------------

Adhoc Rogue Configuration

Detect and report Ad-Hoc Networks................ Enabled

Auto-Contain Ad-Hoc Networks..................... Disabled

Client MAC Address  Adhoc BSSID         State              # APs   Last Heard

------------------  ------------------  -----------------  ------  ------------

----------

Rogue Client Configuration

Validate rogue clients against AAA............... Disabled

--More or (q)uit current module or to abort

MAC Address        State              # APs Last Heard

-----------------  ------------------ ----- -----------------------

Ignore List Configuration

MAC Address

-----------------

Rogue Rule Configuration

Priority Rule Name               State    Type          Match Hit Count

-------- ----------------------- -------- ------------- ----- ---------

Press Enter to continue or to abort

Media-Stream Configuration

Multicast-direct State........................... disable

Allowed WLANs....................................

Stream Name   Start IP       End IP         Operation Status

------------- -------------- -------------- ----------------

URL..............................................

E-mail...........................................

Phone............................................

Note.............................................

State............................................ disable

2.4G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

--More-- or (q)uit

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

5G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

--More-- or (q)uit

Number of Clients................................ 0

Client Mac         Stream Name  Stream Type  Radio WLAN  QoS    Status

-----------------  -----------  -----------  ----  ----  ------ -------

(Cisco Controller) show>

Hall of Fame Super Gold

Operational Status DOWN -WLC 2504 and LAP 3501

Can you console into the WAP and reboot it?  Please post the full output of the entire bootup process.

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Here it is

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)

Board Revision 0.0 (SN: PSJ154208DT, Type: AIR-CT2504-K9) (P)

Verifying boot loader integrity... OK.

OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)

CPU Cores:  4

DRAM:  1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1, octeth2, octeth3

  ' - Active interface

  E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C341105448A12d5BDEYK

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press now to access the Boot Menu...

Loading primary image (7.0.116.0)

100%

31535298 bytes read

Launching...

Launching images...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 672, tty '': '/etc/init.d/rcS'

type = block

dump-device = 254:4

disrupt

level = header

compress = none

ifconfig: SIOCGIFFLAGS: No such device

Detecting Hardware ...

Installing ether-pow driver - 0x6008

starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'

Cryptographic library self-test....passed!

XML config selected

Validating XML configuration

octeon_device_init: found 1 DPs

/dev/fpga: No such device or address

readCPUConfigData: cardid 0x6060001

Cisco is a trademark of Cisco Systems, Inc.

Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.0.116.0

Firmware Version PIC 16.0

Initializing OS Services: ok

Initializing Serial Services: ok

Initializing Network Services: ok

Initializing Licensing Services: ok

Starting ARP Services: ok

Starting Trap Manager: ok

Starting Network Interface Management Services: ok

Starting System Services: ok

Starting Fastpath Hardware Acceleration: ok

Starting Fastpath Console redirect : ok

Starting Fastpath DP Heartbeat : ok

Fastpath CPU00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok

Fastpath CPU00: Initializing last packet received queue. Num of cores(2)

Fastpath CPU00: Init MBUF size: 1856, Subsequent MBUF size: 2040

Fastpath CPU00: Core 0 Initialization: ok

Fastpath CPU01: Core 1 Initialization: ok

Fastpath CPU00: Initializing Timer...

Fastpath CPU00: Initializing Timer...done.

Starting Switching Services: ok

Starting QoS Services: ok

Starting Policy Manager: ok

Starting Data Transport Link Layer: ok

Starting Access Control List Services: ok

Starting System Interfaces: ok

Starting Client Troubleshooting Service: ok

Starting Management Frame Protection: ok

Starting Certificate Database: ok

Starting VPN Services: ok

Starting Licensing Services: ok

Starting LWAPP: ok

Starting CAPWAP: ok

Starting LOCP: ok

Starting Security Services: ok

Starting Policy Manager: ok

Starting Authentication Engine: ok

Starting Mobility Management: ok

Starting Virtual AP Services: ok

Starting AireWave Director: ok

Starting Network Time Services: ok

Starting Cisco Discovery Protocol: ok

Starting Broadcast Services: ok

Starting Logging Services: ok

Starting DHCP Server: ok

Starting IDS Signature Manager: ok

Starting RFID Tag Tracking: ok

Starting Power Supply and Fan Status Monitoring Service: ok

Starting Mesh Services:  ok

Starting TSM: ok

Starting CIDS Services: ok

Starting Ethernet-over-IP: ok

Starting DTLS server:  enabled in CAPWAP

Starting CleanAir: ok

Starting WIPS: ok

Starting SSHPM LSC PROV LIST: ok

Starting RRC Services: ok

Starting FMC HS: ok

Starting Management Services:

   Web Server: ok

   CLI: ok

   Secure Web: ok

   License Agent: ok

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)

User:

User:

Hall of Fame Super Gold

Operational Status DOWN -WLC 2504 and LAP 3501

Errrr ... I meant your WAP and not the WLC 2504.

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

My mistake..... Here you go. Missing the very beginning.

r WRDTR,CLKTR: 0x86000800 0x00000000

r RQDC ,RFDC : 0x80000034 0x00000257

using  eeprom values

WRDTR,CLKTR: 0x86000800 0x00000000

RQDC ,RFDC : 0x80000034 0x00000257

ddr init done

Running Normal Memtest...

Passed.

IOS Bootloader - Starting system.

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................                                                                             ................................................................................                                                                             ................................................................................                                                                             ......

Xmodem file system is available.

DDR values used from system serial eeprom.

WRDTR,CLKTR: 0x86000800, 0x00000000

RQDC, RFDC : 0x80000034, 0x00000257

PCIE0: link is up.

PCIE0: VC0 is active

PCIE1: link is NOT up.

Check PCIe signals to radio, re-seat radio.

PCIE1 port 1 not initialized

64bit PCIE devices

PCIEx: initialization done

flashfs[0]: 31 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31739904

flashfs[0]: Bytes used: 8313856

flashfs[0]: Bytes available: 23426048

flashfs[0]: flashfs fsck took 9 seconds.

Reading cookie from system serial eeprom...Done

Base Ethernet MAC address: e8:b7:48:ac:10:50

Ethernet speed is 1000 Mb - FULL duplex

Loading "flash:/ap3g1-k9w8-mx.124-23c.JA2/ap3g1-k9w8-mx.124-23c.JA2"...#########                                                                             ################################################################################                                                                             ################################################################################                                                                             ################################################################################                                                                             ################################################################################                                                                             ################################################################################                                                                             #######################################################

File "flash:/ap3g1-k9w8-mx.124-23c.JA2/ap3g1-k9w8-mx.124-23c.JA2" uncompressed a                                                                             nd installed, entry point: 0x4000

executing...

enet halted

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA2, RELEASE                                                                              SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 13-Apr-11 12:20 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................                                                                             ................................................................................                                                                             ................................................................................                                                                             ......

flashfs[1]: 31 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31481856

flashfs[1]: Bytes used: 8313856

flashfs[1]: Bytes available: 23168000

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

Radio0  present 8364B 8000 B8020000 0 B8030000 10

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP3501I-A-K9    (PowerPC460exr) processor (revision A0) with 81910K/4                                                                             9152K bytes of memory.

Processor board ID FTX1523E3L1

PowerPC460exr CPU at 666Mhz, revision number 0x18A8

Last reset from power-on

LWAPP image version 7.0.116.0

1 Gigabit Ethernet interface

1 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E8:B7:48:AC:10:50

Part Number                          : 73-12175-05

PCA Assembly Number                  : 800-32268-05

PCA Revision Number                  : A0

PCB Serial Number                    : FOC15163XLD

Top Assembly Part Number             : 800-32902-01

Top Assembly Serial Number           : FTX1523E3L1

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP3501I-A-K9

% Please define a domain-name first.

Press RETURN to get started!

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar  1 00:00:09.654: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t                                                                             est passed

*Mar  1 00:00:09.666: *** CRASH_LOG = YES

*Mar  1 00:00:09.666: Port 0 is not present

*Mar  1 00:00:09.666: 64bit PCIE devicesSecurity Core found.

Base Ethernet MAC address: E8:B7:48:AC:10:50

*Mar  1 00:00:12.277: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state                                                                              to up

*Mar  1 00:00:13.079: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self                                                                              test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process=                                                                              "Init", ipl= 0, pid= 3

*Mar  1 00:00:13.127: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log                                                                              (contains, 1024 messages)

*Mar  1 00:00:13.145:  status of voice_diag_test from WLC is false

*Mar  1 00:00:14.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth                                                                             ernet0, changed state to up

*Mar  1 00:00:15.250: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA2, RELEASE                                                                              SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 13-Apr-11 12:20 by prod_rel_team

*Mar  1 00:00:15.250: %SNMP-5-COLDSTART: SNMP agent on host APe8b7.48ac.1050 is                                                                              undergoing a cold start

*Mar  1 00:10:40.044: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r                                                                             eset

*Mar  1 00:10:41.044: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio                                                                             0, changed state to down

*Mar  1 00:10:52.041: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:10:52.252: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:10:58.927:  status of voice_diag_test from WLC is false

*Mar  1 00:10:58.984: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:10:59.003: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                                                             ource

*Mar  1 00:11:00.003: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                                                             ource

wmmAC status is FALSE

*Feb  1 21:37:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.161.98.20 peer_port: 5246

*Feb  1 21:37:13.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Feb  1 21:37:13.522: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.161.98.20 peer_port: 5246

*Feb  1 21:37:13.522: %CAPWAP-5-SENDJOIN: sending Join Request to 10.161.98.20

*Feb  1 21:37:13.522: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Feb  1 21:37:13.676: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Feb  1 21:37:13.780: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Feb  1 21:37:13.824: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Cisco_e1:da:a4

*Feb  1 21:37:13.871: %LWAPP-3-CLIENTEVENTLOG: SSID e2e50 added to the slot[0]

*Feb  1 21:37:13.871: %LWAPP-3-CLIENTEVENTLOG: SSID TESTING added to the slot[0]

*Feb  1 21:37:13.874: %WIDS-5-ENABLED: IDS Signature is loaded and enabled

User Access Verification

Hall of Fame Super Gold

Operational Status DOWN -WLC 2504 and LAP 3501

Hey, wait a minute.  I've seen this before.

Your 802.11b is disabled on the controller.

Wireless > 802.11b/g/n > Network > General > 802.11b/g Network Status

Or go to Wireless > All Access Points > 802.11b/g/n > WAP of your Choice > Go to the right and you'll see a blue upside-down arrow, hover your cursor over it and choose Configure.

Under Admin Status, make sure it's ENABLE.

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Just checked - enabled on both screens.

Operational Status DOWN -WLC 2504 and LAP 3501

what happens when you go into the radio and manully change it down then up?

Steve

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

It goes down again.

Operational Status DOWN -WLC 2504 and LAP 3501

@Leo, it's enabled

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 2

Number of Active Clients......................... 0

the AP is -A and the regulator is CA(which supports -A AP)

@Heath  Can you try another AP?

Steve

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Ya - I guess I'll have to hunt another one down...

Hall of Fame Super Gold

Re: Operational Status DOWN -WLC 2504 and LAP 3501

@Leo, it's enabled

Awwww ... too bad.

Hey Heath,

Can you console into the WAP (again) and post the output to the command "dir" please?

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Good Morning... Here is the output

APe8b7.48ac.1050#dir

Directory of flash:/

    2  -rwx        6168   Feb 1 2012 21:45:48 +00:00  private-multiple-fs

    5  -rwx      102709   Feb 1 2012 18:23:24 +00:00  event.log

    6  -rwx         275   Feb 1 2012 21:37:13 +00:00  env_vars

    7  drwx         640  Jul 26 2011 07:04:25 +00:00  ap3g1-k9w8-mx.124-23c.JA2

   11  drwx         128   Mar 1 2002 00:09:56 +00:00  ap3g1-rcvk9w8-mx

31481856 bytes total (23166976 bytes free)

APe8b7.48ac.1050#

Hall of Fame Super Gold

Operational Status DOWN -WLC 2504 and LAP 3501

Can you try this:  Monitor > All AP > Details > Choose the WAP in question > under Admin Status > Enable

Go to the Advanced Tab and under Power over Ethernet settings, make sure nothing is ticked.

New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Yes I did that as my first step as I have run into that before.... But this time no luck....

I am blown away that two brand new devices designed to work together are so cumbersome to get working.

Hall of Fame Super Silver

Operational Status DOWN -WLC 2504 and LAP 3501

Well if you are still having issues, you might as well just try to upload the image back onto the wlc. erase the configuration on the wlc and start from scratch.  Might as well put the 7.0.220.0 code on the wlc.

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Upgraded to 7.0.230.0 and nothing has changed.... I beginning to look at the whole WLC option as a piece of CR*P

Hall of Fame Super Silver

Operational Status DOWN -WLC 2504 and LAP 3501

Did you erase the configuration and start from scratch... not a restore from backup either.  That has helped me in the past a few times.

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

Just tried - clear all config in AP and WLC ..... Same issue....

About to go out an buy a Meru

Hall of Fame Super Silver

Operational Status DOWN -WLC 2504 and LAP 3501

Well since you cleared the wlc config... the last thing I would do is this from the console of the AP:

config t

Entered the username and password (Cisco is the default)

debug capwap console cli

erase /all nvram:

[confirm]

undebug all

reload

[confirm]

-Scott
*** Please rate helpful posts ***
New Member

Operational Status DOWN -WLC 2504 and LAP 3501

SAME!!!!!

Loading "flash:/ap3g1-k9w8-mx.124-23c.JA4/ap3g1-k9w8-mx.124-23c.JA4"...#########                                ################################################################################                                ################################################################################                                ################################################################################                                ################################################################################                                ################################################################################                                ##################################################

File "flash:/ap3g1-k9w8-mx.124-23c.JA4/ap3g1-k9w8-mx.124-23c.JA4" uncompressed a                                nd installed, entry point: 0x4000

executing...

enet halted

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA4, RELEASE                                 SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Fri 27-Jan-12 19:44 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................                                ................................................................................                                ................................................................................                                ......

flashfs[1]: 32 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31481856

flashfs[1]: Bytes used: 8317952

flashfs[1]: Bytes available: 23163904

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

Radio0  present 8364B 8000 B8020000 0 B8030000 10

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP3501I-A-K9    (PowerPC460exr) processor (revision A0) with 81910K/4                                9152K bytes of memory.

Processor board ID FTX1523E3L1

PowerPC460exr CPU at 666Mhz, revision number 0x18A8

Last reset from reload

LWAPP image version 7.0.230.0

1 Gigabit Ethernet interface

1 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E8:B7:48:AC:10:50

Part Number                          : 73-12175-05

PCA Assembly Number                  : 800-32268-05

PCA Revision Number                  : A0

PCB Serial Number                    : FOC15163XLD

Top Assembly Part Number             : 800-32902-01

Top Assembly Serial Number           : FTX1523E3L1

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP3501I-A-K9

% Please define a domain-name first.

Press RETURN to get started!

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar  1 00:00:09.563: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t                                est passed

*Mar  1 00:00:09.572: *** CRASH_LOG = YES

*Mar  1 00:00:09.572: Port 0 is not present

*Mar  1 00:00:09.572: 64bit PCIE devicesSecurity Core found.

Base Ethernet MAC address: E8:B7:48:AC:10:50

*Mar  1 00:00:12.183: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state                                 to up

*Mar  1 00:00:12.988: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self                                 test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process=                                 "Init", ipl= 0, pid= 3

*Mar  1 00:00:13.035: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log                                 (contains, 1024 messages)

*Mar  1 00:00:13.054:  status of voice_diag_test from WLC is false

*Mar  1 00:00:14.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth                                ernet0, changed state to up

*Mar  1 00:00:15.152: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA4, RELEASE                                 SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Fri 27-Jan-12 19:44 by prod_rel_team

*Mar  1 00:00:15.152: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a c                                old start

*Mar  1 00:10:40.044: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r                                eset

*Mar  1 00:10:41.044: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio                                0, changed state to down

*Mar  1 00:10:52.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:10:52.208: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:10:58.937:  status of voice_diag_test from WLC is false

*Mar  1 00:10:58.997: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:11:06.468: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                ource

*Feb  3 20:10:47.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i                                p: 10.161.98.20 peer_port: 5246

*Feb  3 20:10:48.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

wmmAC status is FALSE

*Feb  3 20:10:48.522: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully                                 peer_ip: 10.161.98.20 peer_port: 5246

*Feb  3 20:10:48.522: %CAPWAP-5-SENDJOIN: sending Join Request to 10.161.98.20

*Feb  3 20:10:48.522: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Feb  3 20:10:48.682: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Feb  3 20:10:48.786: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Feb  3 20:10:48.830: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Cisco                                _e1:da:a4

*Feb  3 20:10:48.877: %LWAPP-3-CLIENTEVENTLOG: SSID test added to the slot[0]

*Feb  3 20:10:48.881: %WIDS-5-ENABLED: IDS Signature is loaded and enabled

*Feb  3 20:10:48.884: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.                                255 started - CLI initiated

*Feb  3 20:11:22.999: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s                                ource

User Access Verification

Username:

Username:

% Username:  timeout expired!

Hall of Fame Super Silver

Operational Status DOWN -WLC 2504 and LAP 3501

I don't know... I haven't had any issues so far with a 2504.  Might as well open a TAC case so they can actually see your settings.

-Scott
*** Please rate helpful posts ***
16019
Views
0
Helpful
32
Replies
CreatePlease login to create content