Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Prompt never appears in a 2602i access point

Hello:

 

Today I converted an AIR-CAP2602I-A-K9 access point to autonomous using the mode button/tftp method, but no matter what IOS I install (I tried 2 different IOS and also tried entering to Rommon - I am able to change IOS because the procedure I used does not need any command), i never get to see the prompt so that I can introduce commands to configure the AP. It's like it hangs after "succesfully" initializing

 

The only thing I can see all the time are "normal" console messages, and It shows no error message at all.  It happened even before the downgrade.

 

This is where the AP stops, but it is not really hung because console messages could keep showing up. It just never gets to the promt so I can enter some commands. Would not even acept Enter.

Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team

Initializing flashfs...

flashfs[3]: 200 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 14286848
flashfs[3]: Bytes available: 17453056
flashfs[3]: flashfs fsck took 9 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.

Radio0  present 8764 8000 0 A8000000 A8010000 0
Rate table has 244 entries (64 SGI/104 BF variants)

Radio1  present 8764 8000 0 88000000 88010000 4
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-SAP2602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FGL1716S0Q6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: BC:16:65:95:A7:C3
Part Number                          : 73-14588-02
PCA Assembly Number                  : 800-37899-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17151DSW
Top Assembly Part Number             : 800-38356-01
Top Assembly Serial Number           : FGL1716S0Q6
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP2602I-A-K9   

 

Press RETURN to get started!


*Mar  1 00:00:11.819: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar  1 00:00:11.935: FIPS IOS test Image Checksum successful
*Mar  1 00:00:11.935: FIPS IOS test Crypto RNG DEK Key Test successful
*Mar  1 00:00:11.939: FIPS IOS test SHA-1 successful
*Mar  1 00:00:11.939: FIPS IOS test HMAC-SHA1 successful
*Mar  1 00:00:11.939: FIPS IOS test AES CBC 128-bit Encrypt successful
*Mar  1 00:00:11.939: FIPS IOS test AES CBC 128-bit Decrypt successful
*Mar  1 00:00:11.939: FIPS IOS test IOS AES CMAC Encrypt successful
*Mar  1 00:00:11.939: FIPS IOS test IOS CCM Encrypt successful
*Mar  1 00:00:11.939: FIPS IOS test IOS CCM Decrypt successful
*Mar  1 00:00:11.939: FIPS IOS test RSA Signature Generation successful
*Mar  1 00:00:11.939: FIPS IOS test RSA Signature Verification successful
*Mar  1 00:00:11.939: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:18.863: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
*Mar  1 00:00:18.863: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
*Mar  1 00:00:18.863: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
*Mar  1 00:00:18.863: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
*Mar  1 00:00:18.863: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:24.991: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
*Mar  1 00:00:24.991: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
*Mar  1 00:00:24.991: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
*Mar  1 00:00:24.991: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
*Mar  1 00:00:24.991: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar  1 00:00:25.007: initializing dot11 onplus
*Mar  1 00:00:25.259: not a autoconfig enabled device!!!
*Mar  1 00:00:27.039: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:28.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar  1 00:01:13.383: Starting Ethernet promiscuous mode
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Apr 12 07:12:42.003: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Apr 12 07:12:42.011: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
*Apr 12 07:12:42.011: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Apr 12 07:12:42.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Apr 12 07:12:44.651: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
*Apr 12 07:12:44.651: DPAA Initialization Complete
*Apr 12 07:12:44.651: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Apr 12 07:12:44.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
  <--- CURSOR STOPS HERE AND WON'T ACCEPT ENTER OR ANY OTHER  KEYBOARD ACTION

 

Any thoughts?

 

Best regards and thanks in advance

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Are you sure you turned OFF

Are you sure you turned OFF the settings for Flow Control?

4 REPLIES
Hall of Fame Super Blue

Are you sure you turned OFF

Are you sure you turned OFF the settings for Flow Control?

Community Member

Hello Leo: you mean in the

Hello Leo: you mean in the terminal emulator? yes, I did

Community Member

Leo, I'm usign SecureCrt, so

Leo, I'm usign SecureCrt, so I disabled XON/XOFF and DTR/DSR as usual, but was not disabling RTS/CTS, so I did and now it is working. Thank you very much!
 

Hall of Fame Super Blue

I'm a user of SecureCRT since

I'm a user of SecureCRT since 2002.  

 

Thanks for taking the time to rate our posts.  :)

193
Views
0
Helpful
4
Replies
CreatePlease to create content