Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

show inventory AIR-CAP1602I-E-K9

Hello I would like to ask a question.

Should not show any information a "sh inv" command on a not yet joined AIR-CAP1602I-E-K9? Or it only show this info when joined?

Thank you.

2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

Re: show inventory AIR-CAP1602I-E-K9

No, it should give "show inventoy" output even AP is not registered to a controller. Here is an example where AP is not yet register, but it provides inventory output

APccef.488c.fd41#show inventory

NAME: "AP3500", DESCR: "Cisco Aironet 3500 Series (IEEE 802.11n) Access Point"

PID: AIR-CAP3502I-N-K9 , VID: V01, SN: FGL1537S3P1

APccef.488c.fd41#show capwap client rcb

AdminState                  :  ADMIN_ENABLED

SwVer                       :  7.0.116.0

NumFilledSlots              :  2

Name                        :  APccef.488c.fd41

Location                    :  default location

MwarName                    :  

MwarMacAddr                 :  ffff.ffff.ffff

MwarHwVer                   :  0.0.0.0

ApMode                      :  Local

ApSubMode                   :  Not Configured

OperationState              :  DISCOVERY

CAPWAP Path MTU             :  576

LinkAuditing                :  disabled

AP Rogue Detection Mode     :  Enabled

AP Tcp Mss Adjust           :  Disabled

Band Direct                 :  Disabled

Predownload Status          :  None

Auto Immune Status          :  Disabled

HTH

Rasika

**** Pls rate all useful responses ****

VIP Purple

show inventory AIR-CAP1602I-E-K9

HI Jose,

First your AP software is 7.4.1.37

1602I ap minimum IOS support is 7.4.100.0.

For more info about software compatibility matirx:

http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html

Please check this and then try:

Regards

Dont forget to rate helpful posts.

4 REPLIES
VIP Purple

Re: show inventory AIR-CAP1602I-E-K9

No, it should give "show inventoy" output even AP is not registered to a controller. Here is an example where AP is not yet register, but it provides inventory output

APccef.488c.fd41#show inventory

NAME: "AP3500", DESCR: "Cisco Aironet 3500 Series (IEEE 802.11n) Access Point"

PID: AIR-CAP3502I-N-K9 , VID: V01, SN: FGL1537S3P1

APccef.488c.fd41#show capwap client rcb

AdminState                  :  ADMIN_ENABLED

SwVer                       :  7.0.116.0

NumFilledSlots              :  2

Name                        :  APccef.488c.fd41

Location                    :  default location

MwarName                    :  

MwarMacAddr                 :  ffff.ffff.ffff

MwarHwVer                   :  0.0.0.0

ApMode                      :  Local

ApSubMode                   :  Not Configured

OperationState              :  DISCOVERY

CAPWAP Path MTU             :  576

LinkAuditing                :  disabled

AP Rogue Detection Mode     :  Enabled

AP Tcp Mss Adjust           :  Disabled

Band Direct                 :  Disabled

Predownload Status          :  None

Auto Immune Status          :  Disabled

HTH

Rasika

**** Pls rate all useful responses ****

New Member

show inventory AIR-CAP1602I-E-K9

Thanks Raiska,

So this confirms that the AP is wrong?

APbc16.65b6.0fee>show inventory        

APbc16.65b6.0fee>show capwap client rcb

AdminState                  :  ADMIN_ENABLED

SwVer                       :  7.4.1.37

NumFilledSlots              :  0

Name                        :  APbc16.65b6.0fee

Location                    :  default location

MwarName                    :  

MwarMacAddr                 :  0000.0000.0000

MwarHwVer                   :  0.0.0.0

ApMode                      :  Local

ApSubMode                   :  Not Configured

OperationState              :  DISCOVERY

CAPWAP Path MTU             :  576

LinkAuditing                :  disabled

AP Rogue Detection Mode     :  Enabled

AP Tcp Mss Adjust           :  Disabled

Predownload Status          :  None

Auto Immune Status          :  Disabled

RA Guard Status             :  Disabled

Efficient Upgrade State     :  Disabled

Efficient Upgrade Role      :  None

TFTP Server                 :  Disabled

VIP Purple

show inventory AIR-CAP1602I-E-K9

HI Jose,

First your AP software is 7.4.1.37

1602I ap minimum IOS support is 7.4.100.0.

For more info about software compatibility matirx:

http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html

Please check this and then try:

Regards

Dont forget to rate helpful posts.

New Member

show inventory AIR-CAP1602I-E-K9

Thank you very much,

after the upgrade all seems to be OK. I will join the AP tomorrow on our client WLC's.

APbc16.65b6.0fee>show inventory

NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"

PID: AIR-CAP1602I-E-K9 , VID: V01, SN: FGL1720X4GF

APbc16.65b6.0fee>show capwap client rcb

AdminState                  :  ADMIN_ENABLED

SwVer                       :  7.5.1.73

NumFilledSlots              :  2

Name                        :  APbc16.65b6.0fee

Location                    :  default location

MwarName                    :  

MwarMacAddr                 :  ffff.ffff.0000

MwarHwVer                   :  0.0.0.0

ApMode                      :  Local

ApSubMode                   :  Not Configured

OperationState              :  DISCOVERY

CAPWAP Path MTU             :  576

LinkAuditing                :  disabled

AP Rogue Detection Mode     :  Enabled

AP Tcp Mss Adjust           :  Disabled

Predownload Status          :  None

Auto Immune Status          :  Disabled

RA Guard Status             :  Disabled

Efficient Upgrade State     :  Disabled

Efficient Upgrade Role      :  None

TFTP Server                 :  Disabled

382
Views
0
Helpful
4
Replies
CreatePlease to create content