Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Troubleshoot Cisco Airlap 1242 with WLC 4400 Series LWAPP_CLIENT_ERROR_DEBUG: spamHandleCfgReqTimer: Did not recieve the Config response

I have a Problem with my new AIRLAP 1242 to connect with WLC 4400

after debug in my airlap it shows :

Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1240-k9w8-mx.123-7.JX8/c1240-k9w8-mx.123-7.JX8"...######################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.123-7.JX8/c1240-k9w8-mx.123-7.JX8" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.3(7)JX8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 19-Mar-07 01:42 by hqluong
Image text-base: 0x00003000, data-base: 0x004051E0

Initializing flashfs...

flashfs[1]: 9 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 5062144
flashfs[1]: Bytes available: 10936832
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1242AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCW1411U0FZ
PowerPCElvis CPU at 266Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 68:EF:BD:5F:9A:18
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14093XU3
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FCW1411U0FZ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-E-K9

Press RETURN to get started!


*Mar  1 00:00:05.608: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:06.858: %DOT11-2-VERSION_INVALID: Interface Dot11Radio0, unable to find required radio version 581.18
*Mar  1 00:00:06.858: Interface Dot11Radio0, Accepting as a test version of radio firmware
*Mar  1 00:00:06.878: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:07.234: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:08.212: %DOT11-2-VERSION_INVALID: Interface Dot11Radio1, unable to find required radio version 581.18
*Mar  1 00:00:08.212: Interface Dot11Radio1, Accepting as a test version of radio firmware
*Mar  1 00:00:08.232: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar  1 00:00:09.278: %SYS-6-LOGGERSTART: Logger process started
*Mar  1 00:00:09.326: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.3(7)JX8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 19-Mar-07 01:42 by hqluong
*Mar  1 00:00:09.332: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:09.388: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 32 seconds
*Mar  1 00:00:10.271: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:10.332: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  1 00:00:10.332: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:11.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:28.331: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar  1 00:00:28.361: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar  1 00:00:28.362: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar  1 00:00:28.363: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:28.369: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5260 selected
*Mar  1 00:00:28.372: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:28.398: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:28.399: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:28.465: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:29.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:00:29.465: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Translating "CISCO-LWAPP-CONTROLLER.ekahospital.com"...domain server (202.134.0.155)
*Mar  1 00:00:38.351: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.31.xxx.xxx, mask 255.255.255.0, hostname AP68ef.bd5f.9a18

*Mar  1 00:00:38.820: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2417 selected
*Mar  1 00:00:38.827: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5200 selected (203.130.196.5)
*Mar  1 00:00:49.835: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2422 selected
*Mar  1 00:00:49.842: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5220 selected
*Mar  1 00:00:49.851: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar  1 00:00:49.852: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar  1 00:00:49.852: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  1 00:00:50.852: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:50.852: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 18 07:02:25.504: %LWAPP-5-CHANGED: LWAPP changed state to CFG

*Sep 18 07:02:29.288: LWAPP_CLIENT_ERROR: lwapp_name_lookup - Could Not resolve CISCO-LWAPP-CONTROLLER.MYDOMAIN.com
*Sep 18 07:02:30.504: LWAPP_CLIENT_ERROR_DEBUG: spamHandleCfgReqTimer: Did not recieve the Config response

*Sep 18 07:02:30.551: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET CONFIG RESPONSE.
*Sep 18 07:02:30.551: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 5062144
flashfs[0]: Bytes available: 10936832
flashfs[0]: flashfs fsck took 26 seconds.
Base ethernet MAC Address: 68:ef:bd:5f:9a:18
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!

and after that i check in my WLC that shows

Snap_2010.09.17_14h11m43s_003.jpg

AP with Base Radio MAC xx:xx:xx:xx:xx:xx (APxxxx.xxxx.xxxx) is unable to associate.

The reulatory domain configured on it '-e' does not match the controller's country

code: USA

i found that the problem about the region.

question :

1. is it possible to change the region in AIRLAP 1242 or in WLC?

2. if possible how to change it?

INFO :

my first AIRLAP Product/Model Number : AIR-LAP1242AG-A-K9 and my new AIRLAP Product/Model Number : AIR-LAP1242AG-E-K9

1 REPLY
Cisco Employee

Re: Troubleshoot Cisco Airlap 1242 with WLC 4400 Series LWAPP_CL

WLC GUI >> Wireless >> Country >> Select the country.

Regards

Surendra

2187
Views
0
Helpful
1
Replies