Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Unable to get access to wism2

Hello,

I have next issue: 

When i was trying to configure redundancy, i lost access to wism2 module. When i ping service port, it reply me, but i unable to get access via "session slot proc".

some brief information:

cisco WS-C6509-E

SN-1#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  2    4  WiSM 2 WLAN Service Module             WS-SVC-WISM2-K9    SAL1739DEGF

  5    5  Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G       SAL1739D9EL

SN-1#sh run | i wism

wism service-vlan 222

wism module 2 controller 1 allowed-vlan 1-1001,1006-4094

SN-1#sh wism module 2 controller 1 status

WiSM Controller 1 in Slot 2 configured with auto-lag

Operational Status of the Controller : Oper-Up

Service VLAN                         : 222

Service Port                         : 3

Service Port Mac Address             : 6c20.562c.5a61

Service IP Address                   : 192.168.1.101

Management IP Address                : 10.32.252.21

Software Version                     : 7.5.102.0

Port Channel Number                  : 547

Allowed-vlan list                    : 1-1001,1006-4094

Native VLAN ID                       : 1

WCP Keep Alive Missed                : 0

any idea?

Everyone's tags (3)
3 REPLIES

Unable to get access to wism2

Is it possible you have a stale session to the service port?

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

Unable to get access to wism2

Stephen, thanks for the reply.

I have reseted wism2 module a few time and this did't help.

I checked opened sessions by "sh sess" and there is no opened connections.

Maybe, i looking for the wrong place?

New Member

Unable to get access to wism2

Also, a have found a difference between second wism2 module

SN-1(config)#do sh wism module 2 cont 1 sta

WiSM Controller 1 in Slot 2 configured with auto-lag

Operational Status of the Controller : Oper-Up

Service VLAN                         : 999

Service Port                         : 3

Service Port Mac Address             : 6c20.562c.5a61

Service IP Address                   : 192.168.1.101

Management IP Address                : 10.32.252.21

Software Version                     : 7.5.102.0

Port Channel Number                  : 547

Allowed-vlan list                    : 1-1001,1006-4094

Native VLAN ID                       : 1

WCP Keep Alive Missed                : 0

SN-2#sh wism module 2 controller 1 status

WiSM Controller 1 in Slot 2 configured with auto-lag

Operational Status of the Controller : Oper-Up

Service VLAN                         : 999

Service Port                         : 3

Service Port Mac Address             : 6c20.562c.4b61

Service IP Address                   : 192.168.1.102

Management IP Address                : 10.32.252.12

Software Version                     : 7.5.102.0

Port Channel Number                  : 547

Allowed-vlan list                    : 1-1000,1006-4094

WCP Keep Alive Missed                : 0

As you can see there is no native vlan on working wism and i cant turn off it on unavailable wism.

248
Views
0
Helpful
3
Replies