Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

WISM2 BUG OR NOT ?

Hi everyone,

I have a problem with our wism2

we have 2 6513 in VSS, and we have 2 wism modules in different 6513

i configured WISM2 with basic configs

when i use "show wism status" i see

Slot  Controller  Service IP       Management IP    SW Version    Controller Type    Status

----+-----------+----------------+----------------+------------+------------------+---------------

26    1           0.0.0.0          0.0.0.0                       WS-SVC-WISM-2-K9   Service Port Up

42    1           0.0.0.0          0.0.0.0                       WS-SVC-WISM-2-K9   Service Port Up

IT DOESNT SHOW ME SERVICE AND MANAGEMENT IP ADDRESS, BUT IF I CONNECT TO WISM2 BY CONSOLE CABLE ALL IP I CONFIGURED FROM INSTALLATION WIZARD ARE THERE, is tha bug ? why he doest show me

my

service vlan 301

mgmt vlan 302

redundancy vlan 303

here my configs about wism

wism service-vlan 301

wism redundancy-vlan 303

wism switch 1 module 10 controller 1 allowed-vlan 302,303

wism switch 2 module 10 controller 1 allowed-vlan 302,303

wism switch 1 module 10 controller 1 native-vlan 302

wism switch 2 module 10 controller 1 native-vlan 302

wism switch 1 module 10 controller 1 qos trust dscp

wism switch 2 module 10 controller 1 qos trust dscp

my VLAN interfaces (SERVICE, MGMT, REDUNDANCY)


interface Vlan301

ip address 10.30.1.254 255.255.255.0

!

interface Vlan302

ip address 10.30.2.254 255.255.255.0

!

interface Vlan303

no ip address

My wism2 created PORT CHANNELS and 2 interface ( it is the same on my second WISM2)

Te1/10/1               unassigned      YES unset  up                    up

Te1/10/2               unassigned      YES unset  up                    up

GigabitEthernet1/10/3  unassigned      YES unset  up                    up

GigabitEthernet1/10/4  unassigned      YES unset  up                    up


My etherchannel summary

707    Po707(SU)        -        Te1/10/1(P)    Te1/10/2(P)

739    Po739(SU)        -        Te2/10/1(P)    Te2/10/2(P)

Please help

Everyone's tags (1)
13 REPLIES
Bronze

WISM2 BUG OR NOT ?

Hi,

please remove the redundancy VLAN from the allowed VLANs

www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#vlan

then reboot.

New Member

WISM2 BUG OR NOT ?

Yahya,

No it doesnt help, again wism2s dont want to show me there service and management ip i configured via console

New Member

WISM2 BUG OR NOT ?

Any Suggestions ??

Hall of Fame Super Gold

Re: WISM2 BUG OR NOT ?

What IOS is your chassis?

Have you tried moving your WiSM2 to a different slot?  Preferrably in a slot ABOVE the Supervisor Card?

New Member

Re: WISM2 BUG OR NOT ?

Leo,

show version

Cisco IOS Software, s2t54 Software (s2t54-ADVIPSERVICESK9-M), Version 15.1(1)SY1                                                                                                 , RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Wed 01-May-13 12:43 by prod_rel_team

ROM: System Bootstrap, Version 12.2(50r)SYS3, RELEASE SOFTWARE (fc1)

CORE-VSS uptime is 12 minutes

Uptime for this control processor is 14 minutes

System returned to ROM by power on

System image file is "bootdisk:s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin"

Last reload reason: power-on

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C6513-E (M8572) processor (revision ) with 1785856K/262144K bytes of memory.

Processor board ID FXS1727Q3H6

CPU: MPC8572_E, Version: 2.2, (0x80E80022)

CORE: E500, Version: 3.0, (0x80210030)

CPU:1500MHz, CCB:600MHz, DDR:600MHz

L1:    D-cache 32 kB enabled

        I-cache 32 kB enabled

Last reset from power-on

61 Virtual Ethernet interfaces

208 Gigabit Ethernet interfaces

44 Ten Gigabit Ethernet interfaces

2543K bytes of non-volatile configuration memory.

Configuration register is 0x2102

Hall of Fame Super Gold

WISM2 BUG OR NOT ?

Post the output:

sh wism switch 1 module 10 controller 1 status

sh wism switch 2 module 10 controller 1 status

New Member

Re: WISM2 BUG OR NOT ?

CORE-VSS#show wism switch 1 module 10 controller 1 status

WiSM Controller 1 in Slot 26 configured with auto-lag

Operational Status of the Controller : Started KeepAlive

Service VLAN                         : 301

Service Port                         : 3

Service Port Mac Address             : 6c20.562c.3321

Service IP Address                   : 0.0.0.0

Management IP Address                : 0.0.0.0

Software Version                     :

Port Channel Number                  : 707

Allowed-vlan list                    : 302

Native VLAN ID                       : 302

WCP Keep Alive Missed                : 0

CORE-VSS#show wism switch 2 module 10 controller 1 status

WiSM Controller 1 in Slot 42 configured with auto-lag

Operational Status of the Controller : Started KeepAlive

Service VLAN                         : 301

Service Port                         : 3

Service Port Mac Address             : 6c20.562c.3541

Service IP Address                   : 0.0.0.0

Management IP Address                : 0.0.0.0

Software Version                     :

Port Channel Number                  : 739

Allowed-vlan list                    : 302

Native VLAN ID                       : 302

WCP Keep Alive Missed                : 0

Hall of Fame Super Gold

WISM2 BUG OR NOT ?

Native VLAN ID                       : 302

Is this the correct Native VLAN?  I think the Native VLAN should be different to the Management IP address.

New Member

Re: WISM2 BUG OR NOT ?

I made by guide, it worked before, we just turned off VSS and 6513 cant show ip address and connect to wism2

if i connect with a console cable to wisms, everything is fine all ip are configured, maybe problem in service, cause 6513 doesnt show wism2s ip

Hall of Fame Super Gold

WISM2 BUG OR NOT ?

New Member

Re: WISM2 BUG OR NOT ?

Leo,

I configured with your guide, can you answer for this:

If we can yo use in allowed-vlan range our service and redundancy vlans,

if i need an layer 3 interface for redundancy vlan (interface of vlan without ip)

New Member

Re: WISM2 BUG OR NOT ?

Leo,

I reconfigured it now it is fine, but my there is a problem with redundancy between my primary and secondary wism2(HA),

so i saw this

Redundancy Mode = SSO ENABLED

     Local State = MAINTENANCE

      Peer State = UNKNOWN - Communication Down

            Unit = Primary

         Unit ID = 6C:20:56:2C:33:20

Redundancy State = Non Redundant

    Mobility MAC = 6C:20:56:2C:33:20

Maintenance Mode = Enabled

Maintenance cause= Incompatible Software license

Redundancy Management IP Address................. 10.30.2.10

Peer Redundancy Management IP Address............ 10.30.2.20

Redundancy Port IP Address....................... 169.254.2.10

Peer Redundancy Port IP Address.................. 169.254.2.20

it says license are incompatible

here is licenses

License Store: Evaluation License Storage

StoreIndex:  0  Feature: base-ap-count                     Version: 1.0

        License Type: Evaluation

        License State: Active, Not in Use, EULA not accepted

            Evaluation total period:  8 weeks  4 days

            Evaluation period left:  8 weeks  4 days

        License Count: 500 / 0 (Active/In-use)

        License Priority: None

and on my HA WISM2

>show license summary

This is a Controller with HA-SKU license.

                                         The base ap count license has been inherited from the Primary Controller.

                                                                                                                  Inherited Apcount = 100/0 (Active/InUse)

                                                                                                                                                          Any base ap count license on HA-SKU controller is disregarded.

                                       The disregarded license information is as follows..

                                                                                          License Store: Primary License Storage

StoreIndex:  0  Feature: base                              Version: 1.0

        License Type: Permanent

        License State: Active, Not in Use

        License Count: Non-Counted

        License Priority: Medium

License Store: Primary License Storage

StoreIndex:  1  Feature: base-ap-count                     Version: 1.0

        License Type: Permanent

        License State: Active, In Use

        License Count: 100 /100 (Active/In-use)

        License Priority: Medium

License Store: Primary License Storage

--More-- or (q)uit

StoreIndex:  2  Feature: data_encryption                   Version: 1.0

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

License Store: Evaluation License Storage

StoreIndex:  0  Feature: base-ap-count                     Version: 1.0

        License Type: Evaluation

        License State: Inactive

            Evaluation total period:  8 weeks  4 days

            Evaluation period left:  8 weeks  4 days

        License Count: 500 / 0 (Active/In-use)

        License Priority: None

how can i fix that ?

Hall of Fame Super Gold

WISM2 BUG OR NOT ?

Oh this should be easy enough.

Send an email to license@cisco.com and tell them you want to RE-HOST the license of one of your WLC.

Provide the following serial number:

1.  Primary WLC;

2.  Secondary WLC.

507
Views
0
Helpful
13
Replies