Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

ASA 5525 IPS

                   I have a asa 5525 and the license with IPS ,but i dont know How usede the IPS issue.anyone can tell me?

Everyone's tags (2)
1 ACCEPTED SOLUTION

Accepted Solutions
Bronze

Re: ASA 5525 IPS

You would need to re-image IPS

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/idm/idm_system_images.html#wpxref15759

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
14 REPLIES
Bronze

Re: ASA 5525 IPS

Your question is not very clear. Are you unable to connect to IPS ?

From ASA, you can simply issue "session ips" to connect to IPS and configure.

Any specific problem that you are facing ?

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
New Member

ASA 5525 IPS

yes unable to connect to IPS

how can i use the IPS

Bronze

Re: ASA 5525 IPS

This guide should help you out:

http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/modules_ips.html

Let me know what is your exact requirement.

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
New Member

Re: ASA 5525 IPS

can't input “ session 1” in the ASA,

i don't know how active it

Bronze

Re: ASA 5525 IPS

Please use "session ips". I updated my answer above.

http://www.cisco.com/en/US/docs/security/ips/7.1/installation/guide/hw_logging_in.html#wp1072132

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
Cisco Employee

Re: ASA 5525 IPS

Command is "session ips" and you can check the module state using "show module ips" command.

New Member

Re: ASA 5525 IPS

when "session ips "  it note:can't sent message to module

Cisco Employee

Re: ASA 5525 IPS

You need license to be able to use IPS, can you please check if IPS module is enabled on your box.

Please issue "show module ips" command and check the License Status -

# show module ips

................

Mod License Name   License Status  Time Remaining
--- -------------- --------------- ---------------
ips IPS Module     Enabled         perpetual

............

New Member

Re: ASA 5525 IPS

OK ,thank you for your help.

next monday,i will try again.

New Member

Re: ASA 5525 IPS


Bronze

Re: ASA 5525 IPS

You would need to re-image IPS

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/idm/idm_system_images.html#wpxref15759

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
New Member

Re: ASA 5525 IPS

thank you very much

I re-image ips and "show module" and "session IPS"

ciscoasa# show module

Mod Card Type                                    Model              Serial No.

--- -------------------------------------------- ------------------ -----------

  0 ASA 5525-X with SW, 8 GE Data, 1 GE Mgmt, AC ASA5525            FCH1623704D

ips ASA 5525-X IPS Security Services Processor   ASA5525-IPS        FCH1623704D

Mod MAC Address Range                 Hw Version   Fw Version   Sw Version

--- --------------------------------- ------------ ------------ ---------------

  0 a493.4caa.50b3 to a493.4caa.50bc  1.0          2.1(9)8      8.6(1)

ips a493.4caa.50b1 to a493.4caa.50b1  N/A          N/A          7.1(4)E4

Mod SSM Application Name           Status           SSM Application Version

--- ------------------------------ ---------------- --------------------------

ips IPS                            Up               7.1(4)E4

Mod Status             Data Plane Status     Compatibility

--- ------------------ --------------------- -------------

  0 Up Sys             Not Applicable

ips Up                 Up

Mod License Name   License Status  Time Remaining

--- -------------- --------------- ---------------

ips IPS Module     Enabled         perpetual

when loggin IPS display

***LICENSE NOTICE***

There is no license key installed on this IPS platform.

The system will continue to operate with the currently installed

signature set.  A valid license must be obtained in order to apply

signature updates.  Please go to http://www.cisco.com/go/license

to obtain a new license or install a license.

why no license!!

Bronze

Re: ASA 5525 IPS

IPS will continue to work perfectly fine; however for Signature updates, you would require a license.

http://www.cisco.com/en/US/docs/security/asa/asa84/asdm64/configuration_guide/modules_ips.html#wp1104578

Regards,

Sawan Gupta

Thanks & Regards, Sawan Gupta
New Member

ASA 5525 IPS

Hi guys please how do i install the Lincence of Cisco IPS trial- version on my ASA .

7555
Views
0
Helpful
14
Replies
CreatePlease to create content