Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Hi All,

What's the correct pkg file for the IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Kindly confirm the same

8 REPLIES

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

You can find system images for 5.0.x on the following link:

http://www.cisco.com/cgi-bin/tablebuild.pl/ips5-arch

However I would advise to upgrade to a higher major train now (if possible) because 5.0.x is too obsolete now.

Regards

Farrukh

New Member

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

After upgration IPS-4240-K9-sys-1.1-a-5.0-2.img to IPS-4240-K9-sys-1.1-a-6.1-1-E3.img i am getting below message

There is no license key installed on the IPS-4240. The system will continue to operate with the currently installed signature set. A valid license must be obtained in order to apply signature updates. Please go to http://www.cisco.com/go/license

to obtain a new license or install a license. Its not going to promt mode ?

How can i go to ips configuration mode?

Any steps which are to be done first?

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Is there any specific error you are getting?

Did you upgrade directly from 5.0.2 to 6.1.1? You have to follow a specific upgrade path (mentioned in the release notes).....

An absent license should not prevent the sensor from going into the configure mode.

Regards

Farrukh

New Member

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Hi,

No specific error.

Did you upgrade directly from 5.0.2 to 6.1.1?

Yes.

Can u give me to follow a specific upgrade Path .

PL.

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

I just checked the software release notes and your upgrade is supported:

http://www.cisco.com/en/US/docs/security/ips/6.1/release/notes/17173_01.html#wp1211351

Did you try rebooting? Whats the specific model and error? Can you post it here?

Regards

Farrukh

New Member

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Hi,

Model IPS4240.Below error only I'm getting.After that i'm unable to do any thing except switch off and switch on.

There is no license key installed on the IPS-4240. The system will continue to operate with the currently installed signature set. A valid license must be obtained in order to apply signature updates. Please go to http://www.cisco.com/go/license

to obtain a new license or install a license.

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

No this is just a regular message seen on EVERY sensor without a valid license.

There has to be something more. Or else you have to

> Open TAC Case

> Re-Image the appliance using the recovery media

Regards

Farrukh

New Member

Re: IPS-4240-K9-sys-1.1-a-5.0-2.img for pkg

Hi,

I have found out that there is a key required for IOS upgrade version5.1 to 6.1

257
Views
4
Helpful
8
Replies