Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

IPS-SSM password recovery

Hi,

 

I have an ASA 5510 with IPS module enabled and i m trying to recover the login credentials, when trying the hw-module module 1 password-reset cmd returned an ERROR: % Invalid input detected at '^' marker. Please advice how can i recover the login and password

 

 

Thank you

 

# sh module 1 details 

Getting details from the Service Module, please wait...

ASA 5500 Series Security Services Module-10

Model:              ASA-SSM-10

Hardware version:   1.0

Serial Number:      JAF14

Firmware version:   1.0(11)5

Software version:   7.0(2)E4

MAC Address Range:  d0d0.fd52.b4ff to d0d0.fd52.b4ff

Data plane Status:  Up

Status:             Up

Mgmt IP addr:       192.168.1.2                                                 

Mgmt Network mask:  255.255.255.0                                               

Mgmt Gateway:       192.168.1.1                                                 

Mgmt Access List:   192.168.1.155/32                                            

Mgmt web ports:     443                                                         

Mgmt TLS enabled:   true                                                        

sh ver

Cisco Adaptive Security Appliance Software Version 7.0(8) 
Device Manager Version 5.0(8)

Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
Config file at boot was "startup-config"

 

Hardware:   ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CNlite-MC-Boot-Cisco-1.2
                             SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
                             IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.05
 0: Ext: Ethernet0/0         : address is 0024.97f0.433e, irq 9
 1: Ext: Ethernet0/1         : address is 0024.97f0.433f, irq 9
 2: Ext: Ethernet0/2         : address is 0024.97f0.4340, irq 9
 3: Ext: Ethernet0/3         : address is 0024.97f0.4341, irq 9
 4: Ext: Management0/0       : address is 0024.97f0.4342, irq 11
 5: Int: Internal-Data0/0    : address is 0000.0001.0002, irq 11
 6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5

Licensed features for this platform:
Maximum Physical Interfaces : Unlimited 
Maximum VLANs               : 25        
Inside Hosts                : Unlimited 
Failover                    : Active/Standby
VPN-DES                     : Enabled   
VPN-3DES-AES                : Enabled   
Security Contexts           : 0         
GTP/GPRS                    : Disabled  
VPN Peers                   : 150       

1 ACCEPTED SOLUTION

Accepted Solutions
New Member

Hi Hisham, This command is

Hi Hisham,

 

This command is not supported in your softeware version - 7.0(2)E4.  Also IPS module should verision 6 or above.

RRecovering the Password for the ASA 5500 AIP SSM

 

Note To reset the password, you must have ASA 7.2.2 or later.

 

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/cli/cli_troubleshooting.html#wp1139722 

gfgfg

 

gfgf

 

1 REPLY
New Member

Hi Hisham, This command is

Hi Hisham,

 

This command is not supported in your softeware version - 7.0(2)E4.  Also IPS module should verision 6 or above.

RRecovering the Password for the ASA 5500 AIP SSM

 

Note To reset the password, you must have ASA 7.2.2 or later.

 

http://www.cisco.com/en/US/docs/security/ips/7.1/configuration/guide/cli/cli_troubleshooting.html#wp1139722 

gfgfg

 

gfgf

 

140
Views
0
Helpful
1
Replies
CreatePlease login to create content