Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

2801 - installing a vwic21mft-t1/e1 - what slot?

Hi. I've got a new 2801 here and an interface card for it. Now i've got 4 available slots for it, but im sure I read somewhere that if I put this vwic2 card in one of the slots I could damage it.. but I cant find that document now grrrr.

What slot should i go for ?

Thanks! :)

14 REPLIES
Hall of Fame Super Gold

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

It's written on the back of the router. Slot 0 is voice only.

Hope this helps, please rate post if it does!

Silver

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

I currently can't find the doc myself but if I remember correctly doesn't it tell you on the front of the router itself what card you can install in each slot? i.e slot 0 VWIC, slot 1 FXO-FXS.

Regards

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

well what ive got is:

Slot 3 nothing written on it

Slot 2 Only VIC's and WIC's

Slot 1 nothing written on it

Slot 0 Only accepts VIC's

As my card is a VWIC 2 not sure what one I go for

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

on 2801 router all the slots supports VWIC module.

So you can install it on any of the slots.

• 4 slots; 2 slots support HWIC, WIC, VIC, or VWIC type modules

• 1 slot supports WIC, VIC, or VWIC type modules

• 1 slot supports VIC or VWIC type modules

-> Sushil

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

ah ok, well i've slotted it into slot 3. However it doesn't show up when I run the show interface command

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

can you let me know the IOS file name you are running.

you should have minimum IP Voice.

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(9)T7, RE)

System image file is "flash:c2801-spservicesk9-mz.124-9.T7.bin"

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

can you paste the show diag outpu.

Silver

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

Ah, you're using t1/e1. You need to configure the card type

global config>card type e1

If you're running 12.4 spsvcs this should work

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

can you pleae check if you have PVDMs on the router.

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

I've put the card in slot 2.

I've entered the command:

card type e1 0 2

and th LP light lights up green or half a second, then the AL light is amber.

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

can you paste the show diag outpu.

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

WIC/VIC Slot 2:

VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision : 0.0

Top Assy. Part Number : 800-22628-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC12021G7S

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-1MFT-T1/E1

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 FD 41 00 00 C0 46 03 20 00 58 64 05

0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31

0x20: 32 30 32 31 47 37 53 03 00 81 00 00 00 00 04 00

0x30: CB 90 56 57 49 43 32 2D 31 4D 46 54 2D 54 31 2F

0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

New Member

Re: 2801 - installing a vwic21mft-t1/e1 - what slot?

I've put the card in slot 2.

I've entered the command:

card type e1 0 2

and th LP light lights up green or half a second, then the AL light is amber.

515
Views
0
Helpful
14
Replies
CreatePlease to create content