08-08-2012 09:33 PM - edited 03-16-2019 12:37 PM
Hello I have a cisco 2801 router that does not recognize the fxs module. I don't know if this is the right place to ask , I am a bigginer in voice also. If there is something else you need to know about the router please ask me
thank you in advance
Router#sh diag
VIC Slot 0:
2nd generation - FXS Voice daughter card (2 port)
Hardware Revision : 3.1
Top Assy. Part Number : 800-21341-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 01
PCB Serial Number : FOC091445KS
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V
Product (FRU) Number : VIC2-2FXS=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 47 41 03 01 C0 46 03 20 00 53 5D 01
0x10: 42 45 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 30
0x20: 39 31 34 34 35 4B 53 03 00 81 00 00 00 00 04 00
0x30: 89 56 00 00 00 FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
***************************************************************************
Cisco 2801 (revision 5.0) with 360448K/32768K bytes of memory.
Processor board ID
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
2 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
125184K bytes of ATA CompactFlash (Read/Write)
***************************************************************************
Cisco IOS Software, 2801 Software (C2801-ADVENTERPRISEK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1)
***************************************************************************
Router#sh voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
50/0/2 1 efxs up up on-hook idle y
50/0/2 2 efxs up up on-hook idle y
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
08-09-2012 02:36 AM
do you have installed PVDM modul ?
if not, you have to FXO/FXS to work
2811#sh inv
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V06 , SN: FCZ12437060
NAME: "4 Port FE Switch on Slot 0 SubSlot 0", DESCR: "4 Port FE Switch"
PID: HWIC-4ESW , VID: V01 , SN: FOC12387MT0
NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation t
wo port FXS voice interface daughtercard"
PID: VIC2-2FXS , VID: V01 , SN: FOC12134BU3
NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation t
wo port FXS voice interface daughtercard"
PID: VIC2-2FXS , VID: V01 , SN: FOC12134CGY
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 3", DESCR: "VWIC2-1MFT-T1/E1
- 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC15285Q86
NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC1238496V
2811#
and dont forget to rate post if it helps
08-09-2012 02:36 AM
You need PVDM2 modules for the voice port to work.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: