Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN

Hi to all.

Follow is the partial configuration of my CME.

It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.

On each port of the 4FXS DID card happens the following:

If I enable direct-inward-dial

    I can receive calls from PSTN.

     Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.

If I disable direct-inward-dial

    I cannot receive directly calls form PSTN.

          Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.

     Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.

I have half the configuration working.

Where am I wrong?

I really appreciate your help.

Thanks to all.

Giorgio.

!

CME#sh ver

Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)

!

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

!

CME uptime is 2 days, 15 hours, 49 minutes

System returned to ROM by power-on

System restarted at 18:54:45 CDT Fri Aug 2 2013

System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"

Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.

Processor board ID FTX1120A08L

2 FastEthernet interfaces

4 ISDN Basic Rate interfaces

16 terminal lines

4 Voice FXS interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

1948656K bytes of USB Flash usbflash0 (Read/Write)

497448K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

!

!

CME#sh telephony-service

CONFIG (Version=7.1)

=====================

Version 7.1

Cisco Unified Communications Manager Express

!

!

isdn switch-type basic-net3

!

!

voice translation-rule 1

rule 1 /^2929091\(..\)/ /\1/

rule 2 /^2929091\(.\)/ /\1/

rule 3 /^02929091\(..\)/ /\1/

rule 4 /^02929091\(.\)/ /\1/

!

!

voice translation-rule 2

rule 2 /\(.*\)/ /02929091\1/

!

!

voice translation-rule 10

rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn

rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn

!

!     

voice translation-profile PSTN-IN

translate calling 10

translate called 1

!

!

voice translation-profile PSTN-OUT

translate calling 2

!

!

!

interface BRI0/0/0

description Isdn channels 1 & 2

no ip address

isdn switch-type basic-net3

isdn timer T310 60000

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice

isdn send-alerting

isdn sending-complete

isdn static-tei 0

!

interface BRI0/0/1

description Isdn channels 3 & 4

no ip address

isdn switch-type basic-net3

isdn timer T310 60000

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice

isdn send-alerting

isdn sending-complete

isdn static-tei 0

!

interface BRI0/1/0

description Isdn channels 5 & 6

no ip address

isdn switch-type basic-net3

isdn timer T310 60000

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice

isdn send-alerting

isdn sending-complete

isdn static-tei 0

!

interface BRI0/1/1

description not used

no ip address

shutdown

isdn switch-type basic-net3

isdn timer T310 60000

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice

isdn send-alerting

isdn sending-complete

isdn static-tei 0

!

!

voice-port 0/0/0

translation-profile incoming PSTN-IN

translation-profile outgoing PSTN-OUT

compand-type a-law

description Connessione con CO Telecom channels 1 & 2

!

voice-port 0/0/1

translation-profile incoming PSTN-IN

translation-profile outgoing PSTN-OUT

compand-type a-law

description Connessione con CO Telecom channels 3 & 4

!

voice-port 0/1/0

translation-profile incoming PSTN-IN

translation-profile outgoing PSTN-OUT

compand-type a-law

description Connessione con CO Telecom channels 5 & 6

!

voice-port 0/1/1

description Disponibile

!

voice-port 0/2/0

input gain 14

connection plar 83

description Interphone 40

station-id name Citofono

station-id number 40

caller-id enable

!

voice-port 0/2/1

cptone IT

description Ced 35

station-id name CED

station-id number 35

caller-id enable

!

voice-port 0/2/2

cptone IT

description FAX_1 50

station-id name FAX_1

station-id number 50

caller-id enable

!        

voice-port 0/2/3

cptone IT

description FAX_2 60

station-id name FAX_1

station-id number 60

caller-id enable

!

!

dial-peer voice 1001 pots

description **Sends call to PSTN line 1-2**

destination-pattern 0T

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

port 0/0/0

dial-peer voice 2001 pots

description **Receives calls coming from PSTN line 1-2**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/0/0

!

!

dial-peer voice 1003 pots

description **Sends call to PSTN line 3-4**

destination-pattern 0T

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

port 0/0/1

dial-peer voice 2003 pots

description **Receives calls coming from PSTN line 3-4**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/0/1

!

!

dial-peer voice 1005 pots

description **Sends call to PSTN line 5-6**

destination-pattern 0T

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

port 0/1/0

dial-peer voice 2005 pots

description **Receives calls coming from PSTN line 5-6**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/1/0

!

!

dial-peer voice 2035 pots

description **Receives calls coming from PSTN to Extension 35**

answer-address 35

destination-pattern 35$

incoming called-number 35

port 0/2/1

dial-peer voice 2040 pots

description **Receives calls coming from PSTN to Extension 40**

destination-pattern 40

incoming called-number 40

no digit-strip

direct-inward-dial

port 0/2/0

dial-peer voice 2050 pots

description **Receives calls coming from PSTN to Fax 50**

destination-pattern 50

incoming called-number 50

no digit-strip

direct-inward-dial

port 0/2/2

dial-peer voice 2060 pots

description **Receives calls coming from PSTN to Fax 60**

destination-pattern 60

incoming called-number 60

no digit-strip

direct-inward-dial

port 0/2/3

CME#

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

4FXS-DID configuration problem using BRI to receive/send calls f

Remove incoming called-number under dial-peer.

Also progress_ind and various other commands are not needed.

8 REPLIES
Hall of Fame Super Gold

4FXS-DID configuration problem using BRI to receive/send calls f

Remove incoming called-number under dial-peer.

Also progress_ind and various other commands are not needed.

4FXS-DID configuration problem using BRI to receive/send calls f

Thanks Paolo for your fast answer.

But please be more specific.

On which of the dial-peers should I remove the command "incoming called-number"? On FXS dial-peers? Right?

Giorgio.

Hall of Fame Super Gold

Re: 4FXS-DID configuration problem using BRI to receive/send cal

On all of them. Then add a single DP with "incoming-called number ." and direct-inward-dial.

Re: 4FXS-DID configuration problem using BRI to receive/send cal

Hi Paolo.

Sorry for the delay. I was on holiday.

I would like to keep separate incoming calls from outgoing calls.

So I decided to keep two dial peers for every BRI interface.

I followed your suggestion on eliminate commands:

"incoming called-number" on FXSs,

various "progress_ind" on BRIs

Also I eliminated  "direct-inward-dial" on FXSs,

Today I reconfigured and right tested the dial peers as following:

!

!   Bri Interfaces

!

dial-peer voice 1001 pots

description **Sends call to PSTN line 1-2**

destination-pattern 0T

port 0/0/0

!

dial-peer voice 2001 pots

description **Receives calls coming from PSTN line 1-2**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/0/0

!

!

dial-peer voice 1003 pots

description **Sends call to PSTN line 3-4**

destination-pattern 0T

port 0/0/1

dial-peer voice 2003 pots

description **Receives calls coming from PSTN line 3-4**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/0/1

!

!

dial-peer voice 1005 pots

description **Sends call to PSTN line 5-6**

destination-pattern 0T

port 0/1/0

dial-peer voice 2005 pots

description **Receives calls coming from PSTN line 5-6**

destination-pattern 2929091..

incoming called-number .T

direct-inward-dial

port 0/1/0

!

!   FXS interfaces

!

dial-peer voice 2035 pots

description **Receives calls coming from PSTN to Extension 35**

destination-pattern 35

no digit-strip

port 0/2/1

!

!

dial-peer voice 2040 pots

description **Receives calls coming from PSTN to Extension 40**

destination-pattern 40

no digit-strip

port 0/2/0

!

!

dial-peer voice 2050 pots

description **Receives calls coming from PSTN to Fax 50**

destination-pattern 50

no digit-strip

port 0/2/2

!

!

dial-peer voice 2060 pots

description **Receives calls coming from PSTN to Fax 60**

destination-pattern 60

no digit-strip

port 0/2/3

Thanks a lot Paolo. :-)

Giorgio.

Hall of Fame Super Gold

4FXS-DID configuration problem using BRI to receive/send calls f

Thank you for the nice rating and good luck!

New Member

Hello,Pls I need help in

Hello,

Pls I need help in configuring an analog phone connected to VWIC3-4FXS/DID to be able to make pstn calls. currently it is making local calls to IP phones but when PSTN no is dialled, it responds with a fast busy tone. it's unclear why it does this. Appreciate your help.

Hi Emanuel.As my last

Hi Emanuel.

As on my last displayed config, I did configurations for dial peers attached to BRI lines and the four analog faxes.
Pay attention on how you compose the number on analog phone to get POTS. In my case I should manually prepend 0. Any other number will fall on locally configured number or on a busy tone.

If this does not help you enough, please open a new thread and attach your configuration. We will be very glad to help you.

Giorgio.
 

New Member

Hi Giorgio,Thanks for your

Hi Giorgio,

Thanks for your response. I already have my outgoing & incoming dial peers and relevant voice translations configured and currently all IP phones registered on the UC520's CME are working perfectly. They make and receive PSTN calls smoothly with DID through an E1 line.

I was only meant to setup the 4 FXS/DID ports to provide the same functionality for Analog phones. The phones can make on-net calls back and forth with IP Phones, they also receive incoming PSTN calls. However PSTN nos dialed from the Analog phones match the right outgoing dial-peer (seen from debug voice ccapi inout) but then returns a fast busy tone without the call going through.

I have checked everything and can't seem to find the problem, please help! Below is my partial config.

voice-port 0/0/0

station-id number 1234

caller-id enable

 

dial-peer voice 1234 pots

destination-pattern 1234

port 0/0/0

426
Views
0
Helpful
8
Replies
CreatePlease login to create content