07-18-2012 01:51 PM - edited 03-16-2019 12:16 PM
I seem to be having an issue with dialing 911. User is getting dialtone after dialing 911. Here is my config.
dial-peer cor custom
name PSTN
name PBX
name VOIP
!
dial-peer cor list TargetPSTN
member PSTN
!
dial-peer cor list TargetPBX
member PBX
!
dial-peer cor list TargetVOIP
member VOIP
!
dial-peer voice 98 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
destination-pattern 911
incoming called-number 911
port 0/0/1:23
forward-digits 3
!
dial-peer voice 99 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
destination-pattern 911
incoming called-number 911
port 0/0/0:23
forward-digits all
Thanks in advance.
Solved! Go to Solution.
07-19-2012 08:42 AM
Mike
Can you remove the COR
and test again
!
dial-peer voice 98 pots
no corlist incoming TargetPBX
no corlist outgoing TargetPSTN
!
!
dial-peer voice 99 pots
no corlist incoming TargetPBX
no corlist outgoing TargetPSTN
!
Regards,
Alex.
Please rate useful posts.
07-18-2012 01:56 PM
Mike,
Can you post
debug isdn q931 of a failed call
Also the config or info about your sytem
CUCM or CME
Regards,
Alex.
Please rate useful posts.
07-18-2012 02:01 PM
Actually its a temporary Gateway that we have between an NEC and the PSTN , so we can strip DIDs off as people migrate to CUCM. I will work on getting a debug.
Thanks.
07-18-2012 02:41 PM
Hi Mike,
Can you post a debug voip dial-peer and the q931 mentioned above.
Try adding direct-inward-dial to your dial-peers 98 & 99
HTH,
Chris
07-19-2012 07:13 AM
Here is the debug.
*Jul 19 10:18:15.507: ISDN Se0/0/1:23 Q931: RX <- CALL_PROC pd = 8 callref = 0xDFAE
Channel ID i = 0xA98397
Exclusive, Channel 23
*Jul 19 10:18:17.167: ISDN Se0/0/1:23 Q931: RX <- ALERTING pd = 8 callref = 0xDFAE
Progress Ind i = 0x8488 - In-band info or appropriate now available
*Jul 19 10:18:17.175: ISDN Se0/1/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x8100
Progress Ind i = 0x8488 - In-band info or appropriate now available
*Jul 19 10:18:20.831: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0200
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838D
Exclusive, Channel 13
Progress Ind i = 0x8181 - Call not end-to-end ISDN, may have in-band info
Calling Party Number i = 0xA1, '651XXXXXXX'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '911'
Plan:ISDN, Type:National
*Jul 19 10:18:20.843: %ISDN-6-CONNECT: Interface Serial0/1/0:12 is now connected to 651XXXXXXX N/A
*Jul 19 10:18:20.847: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8200
Channel ID i = 0xA9838D
Exclusive, Channel 13
*Jul 19 10:18:20.847: ISDN Se0/1/0:23 Q931: TX -> CONNECT pd = 8 callref = 0x8200
*Jul 19 10:18:20.931: ISDN Se0/1/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0200
*Jul 19 10:18:31.439: ISDN Se0/1/1:23 Q931: RX <- DISCONNECT pd = 8 callref = 0xDF9F
Cause i = 0x8190 - Normal call clearing
*Jul 19 10:18:31.439: %ISDN-6-DISCONNECT: Interface Serial0/1/1:0 disconnected from 4525 , call lasted 942 seconds
*Jul 19 10:18:31.443: ISDN Se0/1/1:23 Q931: TX -> RELEASE pd = 8 callref = 0x5F9F
*Jul 19 10:18:31.447: %ISDN-6-DISCONNECT: Interface Serial0/0/1:0 disconnected from 612XXXXXXX , call lasted 942 seconds
*Jul 19 10:18:31.451: ISDN Se0/0/1:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x8091
Cause i = 0x8090 - Normal call clearing
*Jul 19 10:18:31.499: ISDN Se0/0/1:23 Q931: RX <- RELEASE pd = 8 callref = 0x0091
*Jul 19 10:18:31.503: ISDN Se0/0/1:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8091
*Jul 19 10:18:31.539: ISDN Se0/1/1:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xDF9F
07-19-2012 07:53 AM
Mike,
We see the call is incoming on
S0/1/0:23
*Jul 19 10:18:20.831: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0200
Which dial peer do calls on PORT 0/1/0:23 match
Think you will need to provide more or all of show run
Regards,
Alex.
Please rate useful posts.
07-19-2012 07:57 AM
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-select 1 T1 0/0/0
network-clock-select 2 T1 0/0/1
!
!
ip cef
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
isdn switch-type primary-ni
!
voice-card 0
no dspfarm
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to sip
h323
modem passthrough nse codec g711ulaw
sip
!
!
!
!
!
!
!
!
!
!
voice translation-rule 3
rule 1 /7029/ /6515237029/
!
!
voice translation-profile profile1
translate calling 3
!
!
!
!
!
!
controller T1 0/0/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description PRI coming from the PSTN
!
controller T1 0/0/1
framing esf
linecode b8zs
pri-group timeslots 1-24
description PRI coming from the PSTN
!
controller T1 0/1/0
framing esf
clock source internal
linecode b8zs
pri-group timeslots 1-24
description To Switch
!
controller T1 0/1/1
framing esf
clock source internal
linecode b8zs
pri-group timeslots 1-24
description To Switch
!
!
!
!
!
!
interface FastEthernet0/0
ip address 10.220.41.99 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
!
interface Serial0/0/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
!
interface Serial0/1/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
interface Serial0/1/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
ip default-gateway 10.220.41.1
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.220.41.1
!
!
ip http server
no ip http secure-server
!
logging 10.1.1.95
snmp-server community OSIMonitor RO 5
!
!
!
control-plane
!
!
!
voice-port 0/0/0:23
!
voice-port 0/1/0:23
!
voice-port 0/0/1:23
!
voice-port 0/1/1:23
!
!
!
!
dial-peer cor custom
name PSTN
name PBX
name VOIP
!
!
dial-peer cor list TargetPSTN
member PSTN
!
dial-peer cor list TargetPBX
member PBX
!
dial-peer cor list TargetVOIP
member VOIP
!
!
dial-peer voice 6 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound
destination-pattern [2-9].........$
incoming called-number [1-7]...$
direct-inward-dial
port 0/0/0:23
forward-digits 10
!
dial-peer voice 7 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound
destination-pattern [2-9].........$
incoming called-number [1-7]...$
direct-inward-dial
port 0/0/1:23
forward-digits 10
!
dial-peer voice 8 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound
destination-pattern [2-9]......T
incoming called-number [1-7]...$
direct-inward-dial
port 0/0/1:23
forward-digits 7
!
dial-peer voice 9 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound
destination-pattern [2-9]......T
incoming called-number [1-7]...$
direct-inward-dial
port 0/0/0:23
forward-digits 7
!
dial-peer voice 10 pots
corlist incoming TargetPSTN
corlist outgoing TargetPBX
description Inbound Dialin
translation-profile incoming Outbound
destination-pattern [1-7]...
incoming called-number .
no digit-strip
direct-inward-dial
port 0/1/0:23
!
dial-peer voice 11 pots
corlist incoming TargetPSTN
corlist outgoing TargetPBX
description Inbound Dialin
translation-profile incoming Outbound
destination-pattern [1-7]...
incoming called-number .
no digit-strip
direct-inward-dial
port 0/1/1:23
!
dial-peer voice 22 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound LD
destination-pattern 1..........
no digit-strip
port 0/0/0:23
!
dial-peer voice 23 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
description Outbound LD
destination-pattern 1..........
no digit-strip
port 0/0/1:23
!
dial-peer voice 98 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
destination-pattern 911
incoming called-number 911
port 0/0/1:23
forward-digits 3
!
dial-peer voice 99 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
destination-pattern 911
incoming called-number 911
port 0/0/0:23
forward-digits all
!
dial-peer voice 411 pots
corlist incoming TargetPBX
corlist outgoing TargetPSTN
destination-pattern 411
incoming called-number 411
port 0/0/1:23
forward-digits all
!
dial-peer voice 36 voip
description Connection to CUCM
destination-pattern 6787
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 35 voip
description Connection to CUCM
destination-pattern 7029
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 37 voip
description Connection to CUCM
destination-pattern 6631
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 38 voip
description Connection to CUCM
destination-pattern 6701
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 39 voip
description Connection to CUCM
destination-pattern 6618
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 40 voip
description Connection to CUCM
destination-pattern 6703
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 41 voip
description Connection to CUCM
destination-pattern 6612
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 42 voip
description Connection to CUCM
destination-pattern 6660
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 43 voip
description Connection to CUCM
destination-pattern 6641
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 44 voip
description Connection to CUCM
destination-pattern 6684
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 45 voip
description Connection to CUCM
destination-pattern 6705
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
!
dial-peer voice 46 voip
description Connection to CUCM
destination-pattern 6663
session protocol sipv2
session target ipv4:10.1.100.31
dtmf-relay h245-alphanumeric
07-19-2012 08:10 AM
Mike
Can you add the following as Chris showed earlier:-
!
!
dial-peer voice 98 pots
direct-inward-dial
!
!
dial-peer voice 99 pots
direct-inward-dial
!
Test again
Regards,
Alex.
Please rate useful posts.
07-19-2012 08:32 AM
Still failing. Here is the debug. Thanks.
*Jul 19 11:37:42.339: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0100
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Progress Ind i = 0x8181 - Call not end-to-end ISDN, may have in-band info
Calling Party Number i = 0xA1, '651XXXXXX'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '911'
Plan:ISDN, Type:National
*Jul 19 11:37:42.355: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8100
Channel ID i = 0xA98382
Exclusive, Channel 2
*Jul 19 11:37:42.363: ISDN Se0/1/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x8100
Cause i = 0x8281 - Unallocated/unassigned number
*Jul 19 11:37:42.471: ISDN Se0/1/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x0100
Cause i = 0x8190 - Normal call clearing
*Jul 19 11:37:42.475: ISDN Se0/1/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8100
*Jul 19 11:37:50.431: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0100
*Jul 19 11:37:42.339: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0100
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Progress Ind i = 0x8181 - Call not end-to-end ISDN, may have in-band info
Calling Party Number i = 0xA1, '651XXXXXXX'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, '911'
Plan:ISDN, Type:National
*Jul 19 11:37:42.355: ISDN Se0/1/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8100
Channel ID i = 0xA98382
Exclusive, Channel 2
*Jul 19 11:37:42.363: ISDN Se0/1/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x8100
Cause i = 0x8281 - Unallocated/unassigned number
*Jul 19 11:37:42.471: ISDN Se0/1/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x0100
Cause i = 0x8190 - Normal call clearing
*Jul 19 11:37:42.475: ISDN Se0/1/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8100
*Jul 19 11:37:50.431: ISDN Se0/1/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0100
07-19-2012 08:42 AM
Mike
Can you remove the COR
and test again
!
dial-peer voice 98 pots
no corlist incoming TargetPBX
no corlist outgoing TargetPSTN
!
!
dial-peer voice 99 pots
no corlist incoming TargetPBX
no corlist outgoing TargetPSTN
!
Regards,
Alex.
Please rate useful posts.
07-19-2012 08:53 AM
That did it. Thanks.
Is there a resource for Dial-Peer config? Its either a practice thing or compreshension for me.
07-19-2012 09:01 AM
Mike,
glad it helped.
There are many sources of information for dial peers
here are a couple
http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/dial_peer/dpeer_c.html
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
Regards,
Alex.
Please rate useful posts.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: