Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

A problem with ISDN channels between 2821 and PSTN

There are a PSTN, Cisco 2821 with two E1 ISDN streams and CCM6:

Single scheme:

CCM6 <=(eth)=> GW2821 <=(two E1 controllers)=> PSTN

The problem is that the engineer of digital stations says that first 11 channels in first E1 stream are blocked by station due to some troubles with them.

When I try to see the ISDN status or E1 controllers statuses on GW2821 everything is ok.

How could I find out what is wrong with these first 11 channels in first E1 ?

3 REPLIES
New Member

Re: A problem with ISDN channels between 2821 and PSTN

Hall of Fame Super Gold

Re: A problem with ISDN channels between 2821 and PSTN

Take "debug isdn q931" with "term mon" for a failed call and check.

New Member

Re: A problem with ISDN channels between 2821 and PSTN

#debug isdn q931

Aug 12 10:10:29.067: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0009

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Calling Party Number i = 0x2181, '3842551177'

Plan:ISDN, Type:National

Called Party Number i = 0xA1, '9030678602'

Plan:ISDN, Type:National

Aug 12 10:10:29.103: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8009

Cause i = 0x82AC - Requested circuit/channel not available

Display i = 'REQUESTED CHANNEL NOT AVAILABLE'

Aug 12 10:10:29.123: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8 callref = 0x014B

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Calling Party Number i = 0x2181, '3842551177'

Plan:ISDN, Type:National

Called Party Number i = 0xA1, '9030678602'

Plan:ISDN, Type:National

Aug 12 10:10:29.159: ISDN Se0/0/1:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x814B

Channel ID i = 0xA98381

Exclusive, Channel 1

Aug 12 10:10:32.227: ISDN Se0/0/1:15 Q931: RX <- ALERTING pd = 8 callref = 0x814B

Progress Ind i = 0x8488 - In-band info or appropriate now available

Aug 12 10:10:36.331: ISDN Se0/0/1:15 Q931: RX <- CONNECT pd = 8 callref = 0x814B

Connected Number i = '!', 0x83, '9030678602'

Aug 12 10:10:36.339: ISDN Se0/0/1:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x014B

Aug 12 10:10:40.019: ISDN Se0/0/1:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x014B

Cause i = 0x8A90 - Normal call clearing

Aug 12 10:10:40.039: ISDN Se0/0/1:15 Q931: RX <- RELEASE pd = 8 callref = 0x814B

Aug 12 10:10:40.047: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x014B

As I understand the problem is:

Cause i = 0x82AC - Requested circuit/channel not available

Display i = 'REQUESTED CHANNEL NOT AVAILABLE'

But how to detect why this happens?

264
Views
3
Helpful
3
Replies