Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Ad-hoc off-net conferencing problem

For an off-net ad-hoc conference to work ( the initiator uses a Cisco IP phone, the rest are PSTN callers) is a hardware conference bridge a must? We have only a software conference bridge, it's not working.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Ad-hoc off-net conferencing problem

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729r8

dial-peer voice 10 voip

destination-pattern 50999....

voice-class codec 1

session target ipv4:180.188.179.70

dtmf-relay h245-alphanumeric

no vad

Sorry, codec selection is only available for VoIP dial-peers

you can create another dial-peer with

incoming called-number .

instead of destination-pattern

and set the voice class codec in it to match it as the incoming dial-peer

Here you have some additional info:

A busy tone is received when the user calls across a gateway over a dial peer with a default codec

http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K96009906

voice class codec

http://www.cisco.com/en/US/docs/ios/12_3t/voice/command/reference/vrht_v1_ps5207_TSD_Products_Command_Reference_Chapter.html#wp1106121

HTH

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
4 REPLIES
Cisco Employee

Re: Ad-hoc off-net conferencing problem

It really depends on the codecs you're using within the RTP streams. SW CFB can only handle G711 so if the PSTN streams come in with G729 it will fail

If you're using an H323 gateway you can configure a voice class codec with G711alaw and g711ulaw for the dial-peers you're matching to force the use of this codec.

you can also configure the codec per dial peer but it's easier to configure the voice class codec and apply it to several dial-peers

if you do not have the possibility to change the codec you're using you may need a HW CFB or XCODER

HTH

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: Ad-hoc off-net conferencing problem

Hi Jaime,

Could you please send me a sample config of the voice class codec config & the process of applying it to dial-peers. Can it be applied to pots dial-peers?

Have a nice day.

Regards,

Abhijit.

Cisco Employee

Re: Ad-hoc off-net conferencing problem

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729r8

dial-peer voice 10 voip

destination-pattern 50999....

voice-class codec 1

session target ipv4:180.188.179.70

dtmf-relay h245-alphanumeric

no vad

Sorry, codec selection is only available for VoIP dial-peers

you can create another dial-peer with

incoming called-number .

instead of destination-pattern

and set the voice class codec in it to match it as the incoming dial-peer

Here you have some additional info:

A busy tone is received when the user calls across a gateway over a dial peer with a default codec

http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K96009906

voice class codec

http://www.cisco.com/en/US/docs/ios/12_3t/voice/command/reference/vrht_v1_ps5207_TSD_Products_Command_Reference_Chapter.html#wp1106121

HTH

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: Ad-hoc off-net conferencing problem

Hi Jaime,

Thanks a lot. The issue is resolved now. I configured an IOS enhanced conference bridge on the H.323 gateway ( 2811 router) & evrything works fine.

In fact, before trying this I had tried the steps listed by you a few days back. It didn't work. My guess is that since we were using only a software bridge ( no hardware resource was configured at that time), the system was unable to negiotiate the codec when a voip call leg was established between the Gateway & CCM. I guess that leg was in G.729 while a software bridge talks only G.711.

Thanks & Regards,

Abhijit Das.

168
Views
5
Helpful
4
Replies