Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

adding 2811 as MGCP voice gateway to CUCM 8.x

Hi,

I've copied running config from a 2811 on a CUCM and copied it to a new 2811.  I've changed the IP addresses and I can ping the CUCM from the new 2811, but it doesn't register.  I've added the new 2811 to the CUCM 8.x and configured 1 port for testing, but it will not register - I do get battery on the ports but no DT on the test port I configured.  It was added as an MGCP gateway in the CUCM and the CUCM publisher and subscriber were added to the 2811's config.

Thank you!

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
4 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Hi George,

Can u share the configuration snapshot from Call Manager [Device---Gateway]?

regds,

aman

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

Like Jaime said your missing the bind command, try bouncing the mgcp stack by adding the command "no mgcp, mgcp".

Can u take the output of the following command

Show ccm-manager

Do check if u r putting in the right domain name.

-Kevin


Sent from Cisco Technical Support Android App

Cisco Employee

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

This is an example, adjust as necessary for your environment

mgcp bind control source-interface FastEthernet0/1

mgcp bind media source-interface FastEthernet0/1

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

Mgcp bind control source interface gig 0/0
Mgcp bind media source interface gig 0/0


Sent from Cisco Technical Support Android App

12 REPLIES
New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Inserted below is the majority of the show run ...

          

Building configuration...

Current configuration : 4000 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname test2811

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

logging buffered 51200 warnings

enable secret 5

!

no aaa new-model

clock timezone PST -8

clock summer-time DST recurring

!

ip source-route

!

!

ip cef

!

!

no ip domain lookup

ip domain name testdomain.com

no ipv6 cef

ntp source FastEthernet0/0

multilink bundle-name authenticated

!

!

voice-card 0

!

!

interface FastEthernet0/0

description test LAN

ip address 10.10.10.1 255.255.255.0

duplex auto

speed auto

!

!

!

interface FastEthernet0/1

description production LAN

ip address 139.241.97.9 255.255.255.192

duplex auto

speed auto

!

!

no ip http server

ip http authentication local

!

logging facility local1

!
ip default-gateway 139.241.97.1

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 139.241.97.1

!
!

control-plane
!
!
!
voice-port 0/1/0
echo-cancel coverage 64
description Extension 2051
!
voice-port 0/1/1
echo-cancel coverage 64
description Extension 2052
!
voice-port 0/1/2
echo-cancel coverage 64
description Extension 2053
!
voice-port 0/1/3
echo-cancel coverage 64
description Extension 2054
!
voice-port 0/2/0
echo-cancel coverage 64
description Extension 2055
!
voice-port 0/2/1
echo-cancel coverage 64
description Extension 2056
!
voice-port 0/2/2
echo-cancel coverage 64
description Extension 2057
!
voice-port 0/2/3
echo-cancel coverage 64
description Extension 2058

!

!

!

ccm-manager redundant-host 139.241.97.21

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server 139.241.97.22 139.241.97.21

ccm-manager config

!

mgcp

mgcp call-agent 139.241.97.22 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

mgcp package-capability sst-package

mgcp package-capability pre-package

no mgcp package-capability res-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 ecm

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

dial-peer voice 200 voip

destination-pattern 2095

dtmf-relay h245-alphanumeric

!

dial-peer voice 1 pots

service mgcpapp

port 0/1/0

!

...this continues through port 8 ...

dial-peer voice 999010 pots

service mgcpapp

port 0/1/0

!

...this continues through port 8 ...

Thank you!!!

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
Cisco Employee

adding 2811 as MGCP voice gateway to CUCM 8.x

Have you tried no mgcp/mgcp??

Have you tried binding the signaling to an interface??

Is the proper name being used in CUCM??

Are the right cards/interfaces chosen in CUCM??

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
VIP Purple

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Hi George,

Can u share the configuration snapshot from Call Manager [Device---Gateway]?

regds,

aman

New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

thank you for the input Aman... the 2811's domain name was the issue

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Hi Jaime, thank you for your reply...

Have you tried no mgcp/mgcp??  <--- just tried it and it did not help w/ registration

Have you tried binding the signaling to an interface?? <--- ?? please provide more information on how to accomplish this

Is the proper name being used in CUCM??  <--- yes, double checked

Are the right cards/interfaces chosen in CUCM??  <--- yes

thank you!!

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
Cisco Employee

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

This is an example, adjust as necessary for your environment

mgcp bind control source-interface FastEthernet0/1

mgcp bind media source-interface FastEthernet0/1

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

Like Jaime said your missing the bind command, try bouncing the mgcp stack by adding the command "no mgcp, mgcp".

Can u take the output of the following command

Show ccm-manager

Do check if u r putting in the right domain name.

-Kevin


Sent from Cisco Technical Support Android App

New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Thank you guys for your help!!!

... here is the show ccm-manager before registration ...

test2811#show ccm-manager
MGCP Domain Name: test2811.testdomain.com
Priority        Status                   Host
============================================================
Primary         Registered               139.241.97.22
First Backup    Backup Ready             139.241.97.21
Second Backup   None

Current active Call Manager:    139.241.97.22
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            17:58:51 PST Feb 5 2014 (elapsed time: 00:00:10)
Last MGCP traffic time:         17:58:51 PST Feb 5 2014 (elapsed time: 00:00:10)
Last failover time:             17:57:30 PST Feb 5 2014 from (139.241.97.22)
Last switchback time:           17:58:00 PST Feb 5 2014 from (139.241.97.21)
Switchback mode:                Graceful
MGCP Fallback mode:             Not Selected
Last MGCP Fallback start time:  None
Last MGCP Fallback end time:    None
MGCP Download Tones:            Disabled
TFTP retry count to shut Ports: 2

Configuration Auto-Download Information
=======================================
No configurations downloaded
Current state: Downloading XML file
Configuration Download statistics:
        Download Attempted             : 1
          Download Successful          : 0
          Download Failed              : 0
          TFTP Download Failed         : 20
        Configuration Attempted        : 0
          Configuration Successful     : 0
          Configuration Failed(Parsing): 0
          Configuration Failed(config) : 0
Last config download command:
FAX mode: disable
Configuration Error History:
test2811#
Loading test2811.cnf.xml from 139.241.97.22 (via FastEthernet0/1): !
[OK - 57998 bytes]

This package type is not the default package type.

... here is the show ccm-manager after the domain name was deleted in the 2811's IOS config, which was not matching the CUCM...

Building configuration...

[OK]
*Feb  6 01:59:52.143: %CMAPP-6-CONFIG_DONE: Configuration by CCM is done

test2811#copy run start
Destination filename [startup-config]?
Building configuration...

[OK]
test2811#show ccm-manager
MGCP Domain Name: test2811
Priority        Status                   Host
============================================================
Primary         Registered               139.241.97.22
First Backup    Backup Ready             139.241.97.21
Second Backup   None

Current active Call Manager:    139.241.97.22
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            18:04:06 PST Feb 5 2014 (elapsed time: 00:00:11)
Last MGCP traffic time:         18:04:06 PST Feb 5 2014 (elapsed time: 00:00:11)
Last failover time:             17:57:30 PST Feb 5 2014 from (139.241.97.22)
Last switchback time:           17:58:00 PST Feb 5 2014 from (139.241.97.21)
Switchback mode:                Graceful
MGCP Fallback mode:             Not Selected
Last MGCP Fallback start time:  None
Last MGCP Fallback end time:    None
MGCP Download Tones:            Disabled
TFTP retry count to shut Ports: 2

Configuration Auto-Download Information
=======================================
Current version-id: 1391645659-b582897c-6888-4f3b-8473-44d1776dc967
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
        Download Attempted             : 1
          Download Successful          : 1   <---- cool, thank you
          Download Failed              : 0
          TFTP Download Failed         : 20
        Configuration Attempted        : 1
          Configuration Successful     : 1
          Configuration Failed(Parsing): 0
          Configuration Failed(config) : 0
Last config download command: New Registration
FAX mode: disable
Configuration Error History:
test2811#

I didn't realize that the hostname was bound to the domain name on the 2811's config.  The CUCM only had the hostname in the gateway's config.  As soon as the no ip domain name command was executed, the 2811 registered.  I'll probably be adding the binding commands just to make sure once its in production.  Thank you all for your help - very much appreciated!!!

George

- Job 38:36, - Psalm 116:5

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

thank you for the show ccm-manager input - very useful!

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m

Re:adding 2811 as MGCP voice gateway to CUCM 8.x

Mgcp bind control source interface gig 0/0
Mgcp bind media source interface gig 0/0


Sent from Cisco Technical Support Android App

New Member

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

thank you again Kevin, this is what the production config will be using

"I believe that the greatest work of God has not been in the miraculous, nor in the spectacular, incomprehensible Creation, but rather I believe it was accomplished on the Cross where He Himself purchased the redemption of His Bride... the salvation of m
VIP Purple

Re: adding 2811 as MGCP voice gateway to CUCM 8.x

Hi George,

you can also run show ccm-manager hosts command.

regds,

aman

194
Views
0
Helpful
12
Replies
CreatePlease to create content