Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

adding another T-1

i have a branch office on our IPT system with one t-1 - we want to add another t1. if i multilink these two t-1's will i experience any issues with the voice?

5 REPLIES
Hall of Fame Super Gold

Re: adding another T-1

Not at all.

New Member

Re: adding another T-1

HI,

I was checking the similar requirements. I think there could be voice quality issue due to physical disparities on T1 circuits. If there are errors/delay on one link, there will be packet losses/jitter causing bad quality to all voip connections.

Thanks,

Kapil Atrish

New Member

Re: adding another T-1

i added the multilink last night and ive noticed a strange issue with QOS. i cant add my service policy to one on the interfaces in the multilink.

SSF_CORP#conf t

SSF_CORP(config)#interface Serial0/1/0:0

SSF_CORP(config-if)#service-policy output EWT_SP

SSF_CORP(config-if)#end

SSF_CORP#sh run int Serial0/1/0:0

interface Serial0/1/0:0

description 2ND T-1

bandwidth 1536

ip unnumbered FastEthernet0/0.10

no ip redirects

no ip unreachables

no ip proxy-arp

encapsulation ppp

ip route-cache flow

ip tcp header-compression iphc-format

ppp multilink

ppp multilink group 90

max-reserved-bandwidth 100

ip rtp header-compression iphc-format

ip rtp compression-connections 64

i also get this when i do a sh policy-map interface Serial0/0/0

Queueing [suspended, using FIFO]

what gives?

Hall of Fame Super Gold

Re: adding another T-1

Hi, configure everything you need under multilink i nterface.

New Member

Re: adding another T-1

i have but check this out. one side of the multi i get this during sh policy-map (router 2)-

Class-map: voice-traffic (match-any)

323169 packets, 42269160 bytes

5 minute offered rate 25000 bps, drop rate 0 bps

Match: ip dscp ef (46)

269929 packets, 38969247 bytes

5 minute rate 22000 bps

Match: ip rtp 16384 16383

53240 packets, 3299913 bytes

5 minute rate 0 bps

Queueing

Strict Priority

Output Queue: Conversation 264

Bandwidth 39 (%)

Bandwidth 1198 (kbps) Burst 29950 (Bytes)

(pkts matched/bytes matched) 26101/3192422

(total drops/bytes drops) 0/0

on the other side i get this (Router1)-

Class-map: voice-traffic (match-any)

406971 packets, 52744324 bytes

5 minute offered rate 54000 bps, drop rate 0 bps

Match: ip dscp ef (46)

406971 packets, 52744324 bytes

5 minute rate 54000 bps

Match: ip rtp 16384 16383

0 packets, 0 bytes

5 minute rate 0 bps

Queueing

Strict Priority

Output Queue: Conversation 264

Bandwidth 39 (%)

Bandwidth 1198 (kbps) Burst 29950 (Bytes)

(pkts matched/bytes matched) 0/0

(total drops/bytes drops) 0/0

router 2 -> (pkts matched/bytes matched) 26101/3192422

router 1 -> (pkts matched/bytes matched) 0/0

same config on both sides. im reading a white paper on this now. ideas?

thanks - jerry

103
Views
0
Helpful
5
Replies