Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

All outbound LD calls default to "local" dial-peer

Hello experts,

This is a new small office VoIP setup utilizing a 2851 Integrated Services router. System is fully configured and working for the most part -- internal and local outbound calls work as well as incoming calls. I have 2 dial-peers for outbound calling that i'm concerned about, one for local, one for long-distance.

All outbound calls are matching the first dial-peer "9.......", even though users specifiy "91..........". I'm not sure why. I have COR's setup, but have double-checked to make sure they're acurate.

Any help would be greately appreciated.

COR's and dial-peer config:

!

!

dial-peer cor custom

name internal

name local

name domestic

name international

!

dial-peer cor list call-internal

member internal

!

dial-peer cor list call-local

member local

!

dial-peer cor list call-domestic

member domestic

!

dial-peer cor list call-international

member international

!

dial-peer cor list user-internal

member internal

!

dial-peer cor list user-local

member internal

member local

!

dial-peer cor list user-domestic

member internal

member local

member domestic

!

dial-peer cor list user-international

member internal

member local

member domestic

member international

!

dial-peer voice 1 pots

description ** T1 PRI pots dial-peer **

destination-pattern 911

port 0/1/0:23

forward-digits all

!

dial-peer voice 2 pots

description ** T1 PRI pots dial-peer **

destination-pattern 9911

port 0/1/0:23

forward-digits 3

!

dial-peer voice 3 pots

description ** T1 PRI pots dial-peer **

destination-pattern 9.......

port 0/1/0:23

forward-digits 7

!

dial-peer voice 4 pots

description ** T1 PRI pots dial-peer **

destination-pattern 91..........

port 0/1/0:23

forward-digits 10

prefix 1

!

dial-peer voice 5 pots

corlist outgoing call-international

description ** T1 PRI pots dial-peer **

destination-pattern 9011T

port 0/1/0:23

forward-digits all

!

dial-peer voice 8 pots

description ** T1 PRI pots dial-peer **

incoming called-number .

direct-inward-dial

port 0/1/0:23

!

dial-peer voice 40 voip

description ** cue voicemail pilot number **

translation-profile outgoing PSTN_CallForwarding

destination-pattern 4240

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

!

dial-peer voice 41 voip

description ** cue auto attendant number **

translation-profile outgoing PSTN_CallForwarding

destination-pattern 4250

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

!

Additionally, running a "show dialplan number" on a long-distance number shows a match with dial-peer 3 (local). I can't figure out why???

Any help would be greatly appreciated.

Thanks,

Jad

  • IP Telephony
8 REPLIES
Hall of Fame Super Gold

Re: All outbound LD calls default to "local" dial-peer

Hi, try:

dial-peer voice 3 pots

destination-pattern 9[2-9]......

Hope this helps, please rate post if it does!

New Member

Re: All outbound LD calls default to "local" dial-peer

that didn't change much. I'll start dialing a 10-digit long distance number, but the phone stops at 7-digits and starts calling out.

example:

I dial a local number 123-4567 - matches dial-peer 3 and goes through fine.

I dial a long distance number 1-123-456-7890 - it stops at 1123456.

Hall of Fame Super Gold

Re: All outbound LD calls default to "local" dial-peer

Hi, the example you made should never match DP 3.

Please post output of "show dialplan number 915551234567".

New Member

Re: All outbound LD calls default to "local" dial-peer

That's what i'm thinking...attached.

Hall of Fame Super Gold

Re: All outbound LD calls default to "local" dial-peer

Hi, the output indicates that now you have corlist call-domestic for DP 4, please check that the incoming DP or ephone-dn has also corresponding corlist privileges.

New Member

Re: All outbound LD calls default to "local" dial-peer

yes, both the incoming DP and the ephone-dn are configured with that corlist...

!

dial-peer voice 3 pots

corlist outgoing call-local

description ** T1 PRI pots dial-peer **

destination-pattern 9[2-9]......

port 0/1/0:23

forward-digits 7

!

dial-peer voice 4 pots

corlist outgoing call-domestic

description ** T1 PRI pots dial-peer **

huntstop

destination-pattern 91..........

no digit-strip

port 0/1/0:23

forward-digits 10

prefix 1

ephone-dn 85 dual-line

number 4285

label 4285

description Test Phone

name Visitor 4285

call-forward busy 4240

call-forward noan 4240 timeout 15

corlist incoming user-domestic

hold-alert 30 originator

corlist "user-domestic" and "call-domestic" are members of the same group...

dial-peer cor custom

name internal

name local

name domestic

name international

!

!

dial-peer cor list call-internal

member internal

!

dial-peer cor list call-local

member local

!

dial-peer cor list call-domestic

member domestic

!

dial-peer cor list call-international

member international

!

dial-peer cor list user-internal

member internal

!

dial-peer cor list user-local

member internal

member local

!

dial-peer cor list user-domestic

member internal

member local

member domestic

!

dial-peer cor list user-international

member internal

member local

member domestic

member international

New Member

Re: All outbound LD calls default to "local" dial-peer

I found the issue - the FXO dial-peers were taking presedence. I removed them for now and all is working well.

Thanks for you help!!

New Member

Re: All outbound LD calls default to "local" dial-peer

FYI- Might help someone else....

I ran into the same problem during a recent install of CME4.2. Cisco TAC came up with the following solution:

The reason for the problem is due to the way CME accepts dialed digits. As it accepts digits one by one rather than all at once it will match the 7 digit dial-peer first when you want it to match the 10 digit dial-peer.

This can be overcome by adding a T to the end of the 7 digit dial-peer. This makes the dial-peer wait the length of the inter-digit timeout for more digits to come in. If the inter-digit timeout expires then the 7 digit dial-peer is chosen. If more digits are entered then the next best dial-peer will be chosen (the 10 digit dial-peer assuming 10 digits are entered).

Below is a sample configuration

dial-peer voice XX pots

description LOCAL

destination-pattern 91.......T

port x/x/x

dial-peer voice XX pots

description LONG DISTANCE

destination-pattern 91..........

port x/x/x

321
Views
0
Helpful
8
Replies
This widget could not be displayed.