Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

analog line FXO question for specific users

Dear All

 

 

I have VG h323 with 3 analog lines and CUCM version 7.5 , i want to confiure one of analog lines to go to hunt group and the others two going to specific users

down sample configuration for a specific user.

the configuration i did as following below : please see option 1 , option 2

Option1

In Voice gateway

voice-port 0/2/0
 connection plar opx 3469
 Description ## 22222222##
 caller-id enable
!

dial-peer voice 250 pots
 destination-pattern 9
 port 0/2/0
!

in Call manager

create partition PT-22222222
create CSS  CSS-22222222

add this parttion to gatewat CSS to allow to go out side.

route pattern 9.!#

it is right configuration  ???

 

OR

 

voice-port 3/0
 connection plar opx 222
 caller-id enable
!

dial-peer voice 110 pots
 destination-pattern 9[2569].......
 port 3/0
!
dial-peer voice 120 pots
 destination-pattern 918.....
 port 3/0
 prefix 18
!
dial-peer voice 130 pots
 destination-pattern 91[0-7,9].
 port 3/0
 prefix 1
!
dial-peer voice 140 pots
 incoming called-number .
 direct-inward-dial
!
dial-peer voice 200 pots
 destination-pattern 900T
 port 3/0
 prefix 00
!

 

in option2 , I dont need to configure Route Pattern in CUCM .

 

is it right and which one is better and good for troubleshooting option 1 , or option 2  and is there any missimg in configration in option1 , option2

 

 

thanks.

 

 

2 ACCEPTED SOLUTIONS

Accepted Solutions

HelloFor example , i need

Hello

For example , i need extension 4001 need to call mobile calls  using port 0/0/2. So i need to force call to go out using H323 configuration for a specific port on GW

1)Create PT_Mobile 

2)CSS_CallsToFXO

4)under RP 99XXXXXXXXXX - specify route partition "PT_mobile"

 

on VG

dial-peer voice 100 pots

destination-pattern 99..........

port 0/0/2

forward-digits 10

 

5)Assign CSS for the ext 4001 and for H323 gateway  . dial now from 4001 99XXXXXXXXXX the call go out, if you tried from 4002 as example which not have same CSS - you will be unable to  get cal out. You can use also FAC to assign code before dialing outgoing calls , if you need to avoid partitions and CSS.

You can also take a look for the below:-

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html

Thanks

please rate all useful ifnormation

helloLook we can do as the

hello

Look we can do as the below:-

We can assume that you have 3 X ports 0/0/1 ,. 0/0/2 and 0/0/3.

Lets saye 0/0/1 is for huntgroup users , 0/0/2 and 0/0/3 for specific users.

1-under 0/0/1 , you can configure connection plar xxxx /where xxxx is the hunt pilot which will include Hunt list and under HL , the line group which includes all specific users"..

2-For 0/0/2 and 0/0/3 to allow both of them , only used by specific users , You can configure a code for outgong calls to hit port 0/0/2 or 0/0/3 and allow users to put the code before hit outgoing call for specific port. Of example if i need to go out 0/0/2 you can put code 99 , for 0/0/3 98. 

3-For incoming calls for port 0/0/1 and 0/0/2 , we can use also connection plar opx and assign a xxxx / where the xxxx the extesnion number for your internal user/

 

Note:-Other Solution based on calling number as below:-

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html

 

 

 

Thanks

please rate all useful information

5 REPLIES

Hi Islam, Could please give

Hi Islam,

 

Could please give an example how the outgoing can be configured using PT and CSS.

 

Thanks

HelloFor example , i need

Hello

For example , i need extension 4001 need to call mobile calls  using port 0/0/2. So i need to force call to go out using H323 configuration for a specific port on GW

1)Create PT_Mobile 

2)CSS_CallsToFXO

4)under RP 99XXXXXXXXXX - specify route partition "PT_mobile"

 

on VG

dial-peer voice 100 pots

destination-pattern 99..........

port 0/0/2

forward-digits 10

 

5)Assign CSS for the ext 4001 and for H323 gateway  . dial now from 4001 99XXXXXXXXXX the call go out, if you tried from 4002 as example which not have same CSS - you will be unable to  get cal out. You can use also FAC to assign code before dialing outgoing calls , if you need to avoid partitions and CSS.

You can also take a look for the below:-

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html

Thanks

please rate all useful ifnormation

Hi,Thanks for the reply. So

Hi,

Thanks for the reply.

 

So it means i need to create another route-pattern for extension 4002 with different access-code etc.

 

Please confrim.

 

Thanks

Hi Mahmood Look my friend ,

Hi Mahmood

 

Look my friend , you can do the below:-

1) 1st solution

1- All users use access-code 9 who will use port 0/0/1

2-For some specific users , use access-code 99 for 0/0/2 and access-code 98 for port 0/0/3.

 

2) 2nd solution

Other way which is based on calling number as the below and no need for CSS and partitions or special access code:-

Please take a look for the below:-

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html

Thanks

please rate all useful information

helloLook we can do as the

hello

Look we can do as the below:-

We can assume that you have 3 X ports 0/0/1 ,. 0/0/2 and 0/0/3.

Lets saye 0/0/1 is for huntgroup users , 0/0/2 and 0/0/3 for specific users.

1-under 0/0/1 , you can configure connection plar xxxx /where xxxx is the hunt pilot which will include Hunt list and under HL , the line group which includes all specific users"..

2-For 0/0/2 and 0/0/3 to allow both of them , only used by specific users , You can configure a code for outgong calls to hit port 0/0/2 or 0/0/3 and allow users to put the code before hit outgoing call for specific port. Of example if i need to go out 0/0/2 you can put code 99 , for 0/0/3 98. 

3-For incoming calls for port 0/0/1 and 0/0/2 , we can use also connection plar opx and assign a xxxx / where the xxxx the extesnion number for your internal user/

 

Note:-Other Solution based on calling number as below:-

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/41887-specific-fxs-call.html

 

 

 

Thanks

please rate all useful information

76
Views
4
Helpful
5
Replies
CreatePlease login to create content