02-13-2008 11:28 AM - edited 03-15-2019 08:49 AM
I am new to the VoIP world in Cisco.
I have a 2621 with 2 FXS ports in it. One is being used for Paging.
I need to hook up an analog phone to the second port.
voice-port 1/0/0
!
voice-port 1/0/1
!
!
!
!
!
dial-peer voice 30 pots
destination-pattern 399
port 1/0/0
!
At the directly connected end is a 2811, here is the config for the one the paging that is already set up.
dial-peer voice 40 voip
destination-pattern 399
session target ipv4:10.251.119.1
!
My question is, with this config does it allow the paging port to be used for making and receiving calls?
If so I will just copy the same config for the second port?
I need the second port on the 2621 to be able to make and receive calls.
All calling goes to the 2811 at the other location. There is a T-1 between the two locations.
Thanks,
Rick
02-13-2008 11:31 AM
Hi, seems a regular configuration so far, you call 399, whatever is connected to fxs will receive ring current, and if it goes off-hook, you're connected.
02-13-2008 11:32 AM
Thanks, it just seemed to easy, like I was forgetting something or something else needed to be done.
I will give it a shot.
thanks for the quick response.
02-13-2008 01:04 PM
Ok, I am missing something. I can call the phone from an internal extension, but cannot dial out from the phone. I need to be able to dial internal and external.
What do I need and where can I find it?
Thanks,
Rick
02-13-2008 01:23 PM
Added the following config now:
!
dial-peer voice 32 pots
destination-pattern 90...............
port 1/0/1
forward-digits 16
!
dial-peer voice 33 pots
destination-pattern [2-6]..
port 1/0/1
forward-digits 3
!
dial-peer voice 34 pots
destination-pattern 9[2-9].........
no digit-strip
port 1/0/1
!
dial-peer voice 35 pots
destination-pattern 91..........
no digit-strip
port 1/0/1
!
dial-peer voice 36 pots
destination-pattern #8..
no digit-strip
port 1/0/1
!
When using the phone and trying to dial any number internal, external, LD it give fast busy tone.
02-13-2008 01:55 PM
Hi, convert all the DPs to voip, replace port with session target and the address of the router that has pstn.
02-13-2008 02:02 PM
Before:
!
dial-peer voice 32 pots
destination-pattern 90...............
port 1/0/1
forward-digits 16
!
dial-peer voice 33 pots
destination-pattern [2-6]..
port 1/0/1
forward-digits 3
!
dial-peer voice 34 pots
destination-pattern 9[2-9].........
no digit-strip
port 1/0/1
!
dial-peer voice 35 pots
destination-pattern 91..........
no digit-strip
port 1/0/1
!
dial-peer voice 36 pots
destination-pattern #8..
no digit-strip
port 1/0/1
After:
!
dial-peer voice 32 voip
destination-pattern 90...............
session target ipv4:10.251.118.1 1/0/1
forward-digits 16
!
dial-peer voice 33 voip
destination-pattern [2-6]..
session target ipv4:10.251.118.1 1/0/1
forward-digits 3
!
dial-peer voice 34 voip
destination-pattern 9[2-9].........
no digit-strip
session target ipv4:10.251.118.1 1/0/1
!
dial-peer voice 35 voip
destination-pattern 91..........
no digit-strip
session target ipv4:10.251.118.1 1/0/1
!
dial-peer voice 36 voip
destination-pattern #8..
no digit-strip
session target ipv4:10.251.118.1 1/0/1
The question I have with this now is will it affect the current dial peers on the 2811 router at the head office where all the IP phones connect to?
Is this config correct to apply?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: