11-04-2013 01:53 AM - edited 03-16-2019 08:13 PM
Hi Experts,
I have one Cisco AS5400 with E1 and PVDMII-64 modules on it. I want to add this AS54 as a voice gateway in Call manager 8.5, is it possible? how? Is there any guide? or steps?
Thank you for your help.
Br
Amir
Solved! Go to Solution.
11-04-2013 02:27 AM
Hi Amir,
For. H.323 , u can refer these DOC
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080094636.shtml
https://supportforums.cisco.com/docs/DOC-24318
For MGCP
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00801ad22f.shtml
regds,
aman
11-04-2013 02:28 AM
This document shows you how to add h323 gateway in cucm.
https://supportforums.cisco.com/docs/DOC-24318
Once you have added the gateway to cucm, you then need to configure your gateway as follows:
1. configure the interface that will be used for h323 signalling..
interface
h323-gateway voip interface
h323-gateway voip bind srcaddr X.X.X.X
2. Configure your dial-peers.
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
11-04-2013 02:08 AM
Amir,
I believe you can add this as a h323 gateway in cucm or create a sip trunk to the gateway in cucm.
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
11-04-2013 02:15 AM
Hi Amir,
please refer the datasheet which says it can be configured for H.323, MGCP and SIP.
http://www.cisco.com/en/US/products/hw/univgate/ps505/products_data_sheet09186a0080091e51.html
Could not find any DOC but I think config would be somewhat similat to other ISR /ISRG2 routers
regds,
aman
11-04-2013 02:20 AM
Hi,
Thank you for your comments, I was looking for a guide to show me how to configure step by step. actually I don't have time to look after commands.
Br
Amir
11-04-2013 02:27 AM
Hi Amir,
For. H.323 , u can refer these DOC
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080094636.shtml
https://supportforums.cisco.com/docs/DOC-24318
For MGCP
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00801ad22f.shtml
regds,
aman
11-04-2013 02:28 AM
This document shows you how to add h323 gateway in cucm.
https://supportforums.cisco.com/docs/DOC-24318
Once you have added the gateway to cucm, you then need to configure your gateway as follows:
1. configure the interface that will be used for h323 signalling..
interface
h323-gateway voip interface
h323-gateway voip bind srcaddr X.X.X.X
2. Configure your dial-peers.
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
11-04-2013 03:19 AM
Hi,
Finally fixed it. That was perfect document.
Many thanks to Amanso and Aokalawon.
Br
Amir
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: