Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

ATA 187 remove ITL CTL files

Hi tecizzz,

How to delete ITL CTL files in ATA 187.

 

Thanks

2 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

I am not a hundred percent

I am not a hundred percent sure, but try connecting a phone to the ATA 187 port 1, and press the Setup button. This should start up an IVR on the ata. Default pin is 24726. This should take you to a menu where you can configure larger settings on the ata.

Cisco Employee

HiYou should be getting the

Hi

You should be getting the following options:

 Navigating the IVR Configuration Menu 

 
Action
 
IVR Code
 
Navigating Notes
 

Review or Set Network Settings

 

1

 

If DHCP is enabled, the IVR announces each network parameter.

 

If DHCP is disabled, the IVR announces each network parameter, pausing in between to allow you to enter a new value.

 

1. IVR announces the IP Address. To change the IP address for the phone, use the keypad to enter a new IP address, followed by the #. To retain the current IP address, press #.

 

2. IVR announces the subnet mask. To change the subnet mask use the keypad to enter a new IP address, followed by the #. To retain the current subnet mask, press #.


 

Note To enter the dot "." that separates each octet in the IP address, press *.


 

3. IVR announces the default gateway. To change the default gateway, use the keypad to enter a new IP address, followed by the #. To retain the current default gateway, press #.

 

Review or Set TFTP Server

 

2

 

IVR announces the current TFTP setting.

 

To change the TFTP server, use the keypad to enter a new IP address, followed by the #. To retain the current TFTP server, press #.

 

To reset a TFTP server back to the TFTP server set by the DHCP server from a manually configured TFTP server, press *.

 

Note To enter the dot "." that separates each octet in the IP address, press *.

 

Enable or Disable DHCP

 

3

 

Press 3 to toggle DHCP to enable or disable.

 

Review or Set the VLAN ID

 

4

 

Press 4 to review and set the Administrator VLAN ID.

 

Reset to factory settings

 

0

 

 

Note All configuration settings will reset to default factory settings, the and phone will reset. It will take some time for the phone to re-register. Select this option only when needed.

 

 

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/187/1_0/english/administration/guide/sip/187adm80/a187_agBcd.html

 

No separate option for deleting ITL/CTL files, You will to use factory reset, but ensure you have  all the configuration pre-hand, such as ip, VLAN ,tftp etc 

 

10 REPLIES
Cisco Employee

I am not a hundred percent

I am not a hundred percent sure, but try connecting a phone to the ATA 187 port 1, and press the Setup button. This should start up an IVR on the ata. Default pin is 24726. This should take you to a menu where you can configure larger settings on the ata.

New Member

Thanks for the response.Where

Thanks for the response.

Where is the setup button in the analog phone.(port 1 is the fxs port).

 

Thanks

 

Cisco Employee

The setup button is on the

The setup button is on the ata, not on the analog phone.

You will have to go off-hook on the first line of the ata and then press the setup button on the ata 187.

New Member

I could not see the setup

I could not see the setup button in ATA 187.

please help me.

Cisco Employee

It's the right most LED on

It's the right most LED on the front of your ATA

 

Regards

Aditya

New Member

Thanks for the replay.Could

Thanks for the replay.

Could you please send me the picture?

 

Cisco Employee

attached

attached

New Member

Hi aditgup,ITL -CTL option is

Hi aditgup,

ITL -CTL option is there in the IVR menu?

 

Thanks

Cisco Employee

HiYou should be getting the

Hi

You should be getting the following options:

 Navigating the IVR Configuration Menu 

 
Action
 
IVR Code
 
Navigating Notes
 

Review or Set Network Settings

 

1

 

If DHCP is enabled, the IVR announces each network parameter.

 

If DHCP is disabled, the IVR announces each network parameter, pausing in between to allow you to enter a new value.

 

1. IVR announces the IP Address. To change the IP address for the phone, use the keypad to enter a new IP address, followed by the #. To retain the current IP address, press #.

 

2. IVR announces the subnet mask. To change the subnet mask use the keypad to enter a new IP address, followed by the #. To retain the current subnet mask, press #.


 

Note To enter the dot "." that separates each octet in the IP address, press *.


 

3. IVR announces the default gateway. To change the default gateway, use the keypad to enter a new IP address, followed by the #. To retain the current default gateway, press #.

 

Review or Set TFTP Server

 

2

 

IVR announces the current TFTP setting.

 

To change the TFTP server, use the keypad to enter a new IP address, followed by the #. To retain the current TFTP server, press #.

 

To reset a TFTP server back to the TFTP server set by the DHCP server from a manually configured TFTP server, press *.

 

Note To enter the dot "." that separates each octet in the IP address, press *.

 

Enable or Disable DHCP

 

3

 

Press 3 to toggle DHCP to enable or disable.

 

Review or Set the VLAN ID

 

4

 

Press 4 to review and set the Administrator VLAN ID.

 

Reset to factory settings

 

0

 

 

Note All configuration settings will reset to default factory settings, the and phone will reset. It will take some time for the phone to re-register. Select this option only when needed.

 

 

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/187/1_0/english/administration/guide/sip/187adm80/a187_agBcd.html

 

No separate option for deleting ITL/CTL files, You will to use factory reset, but ensure you have  all the configuration pre-hand, such as ip, VLAN ,tftp etc 

 

New Member

Thanks you all

Thanks you all

920
Views
0
Helpful
10
Replies
CreatePlease to create content