Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Attendant Console and Parking Calls CUCM 6.0

I'm so close ...

Worked my way through the Cisco documentation and have Attendant console almost operational. The only thing that doesn't work is the display of parked calls.

When a call is handled from the AC and parked, it doesn't seem to show in the Parked Call window. However, if it is retrieved and parked from the deskset, it does show in the window.

I'm aware of the settings needed to allow parked call monitoring, and have checked that.

Anybody have any ideas?

13 REPLIES
Hall of Fame Super Red

Re: Attendant Console and Parking Calls CUCM 6.0

Hi David,

Is the Pilot Point Associated/Controlled by the AC User?

Rob

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

I've run into this same problem on CM 6.1. Did you find a resolution to your problem?

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

Hi,

I have the same problem with CUCM ver.6.1(2).

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

I found out this is a Cisco known issue and it isn't supported. You can try creating different park slots and different partitions for your sub and pub.

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

Thanks for the info.

Tomorrow I 'll try .

I will Know you

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

Hi,

test KO. I have configured a different range of call-park number but the problem remains.

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

I had a similar issue and found that it displays parked calls if you have configured the attendant group with the user account rather than the directory number for the operators phone. If you use the directory number it does not display the parked calls until you have retrieved the call and parked it again.

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

I have configured in hunting group only the user ac and not the DN of the operators.

Re: Attendant Console and Parking Calls CUCM 6.0

Hello all,

One of my customers was having the same issue w/CUCM 6.0...we never were able to come to a resolution.

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

We are also having an issue with this. Has there been any update / fix? Some calls show up, most do not.

ANy information would be helpful.

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

We are running into a similar situation where the parked calls are displayed only about 25% of the time, it is very frustrating for the customer. Internal calls seem to always work, calls from external sources are hit or miss (usually miss).

We have tried just about every configuration we could think of in order to facilitate this service for them, and are currently working with TAC to resolve. It doesn't look good though as this case has been open for nearly a month (this time), and we have been working on it for nearly 4 months (with a previous TAC case).

Any suggestions out there?

New Member

Re: Attendant Console and Parking Calls CUCM 6.0

Anyone have any new information on this situation? We have the same issues, so just checking on any updates and anyone might have.

thanks

Robin

Re: Attendant Console and Parking Calls CUCM 6.0

Hi Devogal !!!

can you share the docs of cisco which you used for configure Attendant console !! bcoz i require that and i have to configure it .... if you can share then it will be very appreciated ...

Regards

205
Views
0
Helpful
13
Replies
CreatePlease to create content