Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

bailout DLCB is NULL

Hi.

when i do a incoming call i can read this with the debug.

029998: Nov 17 15:21:26.761 PCTime: ISDN BR0/0/0 SERROR: L2_Go: at bailout DLCB is NULL

L2: sapi 0 tei 127 ces 0 ev 0x3

When is outgoing , using "isdn test call interface bri 0/0/0 948xxxxxx

030033: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 SERROR: isdn_get_display_text_from_gtd: false ret

030034: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 SERROR: isdn_get_mlpp_from_gtd: MLPP from GTD failed

030035: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: CCBRI_Go: source id 0x500, state 0, call id 0x0, event 0x1

030036: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: CCBRI_Go: call id 0x8004 callref 0x0 state 1 event 0x1 Src->HOST

030037: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 0 ie_allowed =1

030038: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 3 ie_allowed =1

030039: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 5 ie_allowed =1

030040: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 7 ie_allowed =1

030041: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 8 ie_allowed =1

030042: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 9 ie_allowed =0

030043: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 10 ie_allowed =0

030044: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 12 ie_allowed =1

030045: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 26 ie_allowed =0

030046: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 15 ie_allowed =1

030047: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 16 ie_allowed =1

030048: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 17 ie_allowed =1

030049: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 19 ie_allowed =1

030050: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 21 ie_allowed =0

030051: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 22 ie_allowed =1

030052: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 23 ie_allowed =1

030053: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 24 ie_allowed =1

030054: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 25 ie_allowed =1

030055: Nov 17 15:24:24.401 PCTime: ISDN BR0/0/0 CC: ie_in_out_msg: message 0x80 ie = 4 ie_allowed =1

030056: Nov 17 15:24:32.401 PCTime: ISDN BR0/0/0 CC: CCBRI_Go: source id 0x300, state 1, call id 0x8004, event 0x341

030057: Nov 17 15:24:32.401 PCTime: ISDN BR0/0/0 CC: CCBRI_Go: call id 0x8004 call ref 0x3 state 6 event 0x91 Src->L3

030058: Nov 17 15:24:32.401 PCTime: ISDN BR0/0/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8004

I check this with 4 ISDN terminal's

thanks

Alfonso

8 REPLIES
Hall of Fame Super Gold

Re: bailout DLCB is NULL

Which exact IOS is this?

If you deconfigure MGCP completely, can you make "test call" ?

New Member

Re: bailout DLCB is NULL

Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(3h), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 25-Jul-07 19:43 by stshen

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

MUTILVACISCO3825 uptime is 1 day, 5 hours, 45 minutes

System returned to ROM by reload at 12:28:18 PCTime Fri Nov 16 2007

System restarted at 11:30:43 PCTime Fri Nov 16 2007

System image file is "flash:c3825-spservicesk9-mz.124-3h.bin"

About the other custion, when i deconfigure MGCP, then "test call" have the same error.

Hall of Fame Super Gold

Re: bailout DLCB is NULL

Hi,

Please upgrade to 12.4(17) mainline, or 12.4(11)XJ4, and try again.

New Member

Re: bailout DLCB is NULL

Hi.

I upgrade to 12.4(17).

Now no error's en BRI interface, but have a new problem.

Then i do incoming call, the ip phone ring only 2 times and stop.

TEI for layer 2 is all time Up, Down, up down.

I wait your notices

Regrdas

Alfonso

Hall of Fame Super Gold

Re: bailout DLCB is NULL

Hi,

As I said before, that circuit appears defective to me.

You can enable "debug isdn q921" and "debug isdn q931", when making or receiving a call. Chances are, it will show again that the switch is disconnecting layer2.

New Member

Re: bailout DLCB is NULL

hi.

debug :

001470: *Nov 19 21:24:51.739 PCTime: ISDN BR0/0/0 Q921: User RX <- UI sapi=0 tei=127

001471: *Nov 19 21:24:51.739 PCTime: ISDN BR0/0/0 Q931: SETUP pd = 8 callref = 0x27

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x89

Calling Party Number i = 0x0183, '948741712'

Plan:ISDN, Type:Unknown

Called Party Number i = 0xA1, '948290007'

Plan:ISDN, Type:National

001472: *Nov 19 21:24:53.863 PCTime: ISDN BR0/0/1 Q921: User TX -> RRp sapi=0 tei=68 nr=0

001473: *Nov 19 21:24:53.867 PCTime: ISDN BR0/0/1 Q921: User RX <- RRp sapi=0 tei=68 nr=0

001474: *Nov 19 21:24:53.867 PCTime: ISDN BR0/0/1 Q921: User TX -> RRf sapi=0 tei=68 nr=0

001475: *Nov 19 21:24:53.875 PCTime: ISDN BR0/0/1 Q921: User RX <- RRf sapi=0 tei=68 nr=0

001476: *Nov 19 21:24:55.971 PCTime: ISDN BR0/0/0 Q921: User RX <- UI sapi=0 tei=127

001477: *Nov 19 21:24:55.971 PCTime: ISDN BR0/0/0 Q931: SETUP pd = 8 callref = 0x27

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x89

Calling Party Number i = 0x0183, '948741712'

Plan:ISDN, Type:Unknown

Called Party Number i = 0xA1, '948290007'

Plan:ISDN, Type:National

001478: *Nov 19 21:24:57.371 PCTime: ISDN BR0/0/0 Q921: User RX <- UI sapi=0 tei=127

001479: *Nov 19 21:24:57.371 PCTime: ISDN BR0/0/0 Q931: SETUP pd = 8 callref = 0x26

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x8A

Progress Ind i = 0x8483 - Origination address is non-ISDN

Calling Party Number i = 0x0183, '948187558'

Plan:ISDN, Type:Unknown

Called Party Number i = 0xA1, '948290007'

Plan:ISDN, Type:National

001480: *Nov 19 21:24:58.855 PCTime: ISDN BR0/0/1 Q921: User RX <- DISCp sapi=0 tei=68

001481: *Nov 19 21:24:58.855 PCTime: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0/0/1, TEI 68 changed to down

001482: *Nov 19 21:24:58.855 PCTime: ISDN BR0/0/1 Q921: User TX -> UAf sapi=0 tei=68

001483: *Nov 19 21:24:58.859 PCTime: ISDN BR0/0/1 Q921: L2_EstablishDataLink: sending SABME

001484: *Nov 19 21:24:58.859 PCTime: ISDN BR0/0/1 Q921: User TX -> SABMEp sapi=0 tei=68

001485: *Nov 19 21:24:58.871 PCTime: ISDN BR0/0/1 Q921: User RX <- UAf sapi=0 tei=68

001486: *Nov 19 21:24:58.871 PCTime: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0/1, TEI 68 changed to up

001487: *Nov 19 21:25:01.143 PCTime: ISDN BR0/0/1 Q921: User RX <- UI sapi=0 tei=127

001488: *Nov 19 21:25:01.143 PCTime: ISDN BR0/0/1 Q931: SETUP pd = 8 callref = 0x0F

Sending Complete

Bearer Capability i = 0x8890

Standard = CCITT

Transfer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x89

Calling Party Number i = 0x0183, '948741712'

Plan:ISDN, Type:Unknown

Called Party Number i = 0xA1, '948291374'

Plan:ISDN, Type:National

001489: *Nov 19 21:25:01.147 PCTime: ISDN BR0/0/1 Q921: User TX -> INFO sapi=0 tei=68, ns=0 nr=0

001490: *Nov 19 21:25:01.147 PCTime: ISDN BR0/0/1 Q931: RELEASE_COMP pd = 8 callref = 0x8F

Cause i = 0x80C1 - Bearer capability not implemented

001491: *Nov 19 21:25:01.163 PCTime: ISDN BR0/0/1 Q921: User RX <- RR sapi=0 tei=68 nr=1

001492: *Nov 19 21:25:01.487 PCTime: ISDN BR0/0/0 Q921: User RX <- UI sapi=0 tei=127

001493: *Nov 19 21:25:01.487 PCTime: ISDN regards

Hall of Fame Super Gold

Re: bailout DLCB is NULL

Hi,

for the first call, the switch is disconnecting L2 without apparent reason:

001480: *Nov 19 21:24:58.855 PCTime: ISDN BR0/0/1 Q921: User RX <- DISCp sapi=0 tei=68

The last call was placed for "unrestricted digital" so I don know who was being called, but if a voice device, is normal that the switch responds "bearer capability no implemented".

Sorry if I can help you more, but it seems to me there is MGCP involved and that makes everything more difficult.

New Member

Re: bailout DLCB is NULL

i have more information.

0x82E6333033 - Recovery on timer expiry

Now, this is de q931 debug

| Q.931 message = 08013A05A104038090A31801816C0B0183393438323335323530700AA13934383135333130387D029181

000204: *Nov 20 09:22:15.471 PCTime: ISDN BR0/0/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x3A

Cause i = 0x82E6333033 - Recovery on timer expiry

000205: *Nov 20 09:22:15.471 PCTime:

can you help me again??

Regards

alfonso

3805
Views
0
Helpful
8
Replies