Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear allI am using Cisco AS5xxx as the media gateway to carry voip calls from IP to PSTN. When checking the accounting logs i see some calls with Calling-Station-ID is "Restricted" . And then the PSTN network drop these calls.How can i solve this pro...
Hi allI have a H323 gateway with ISDN to PSTN.Call comes in from PSTN, hits dial peer to CUCM 8 hunt pilot (broadcast hunt), then call forward to AA. I want the users to be able to CFWDall to another destination when they need to (if they all go int...
I wish to migrate from a CUCM 7.0(1) cluster to a CUCM 8.6.2 cluster on the same hardware. I haven't founda definitive guide to doing so. I would appreciate it if you could direct me to instructions, and could tell me if in fact it is at all possible...
HiFor a small office setup with 70 users is cisco 2921 running Version 15.1(4)M4 an recommended option How do we check which IP Phone model is supported with above version. We also got 5 pieces of Cisco Cius Tablet, can these be registered on CME Te...
Hi all,we are adding new router 3925 and VWIC3-2MFT-T1/E1 to call manager 6.1(5) with mgcp gatewaybase on datasheet of VWIC3-2MFT-T1/E1 is supported on release 15.0(1)M3, 15.1(1)T, and 15.1(2)T --> no issue with thatbase on datasheet of VWIC3-2MFT-T1...
Hi everyone,Happy new year to all.I have one question to our experts.1 - Today i received from customer a strange e-mail asking if they can forward the calls of two extensions to mobile after working hours and they needed to be automatic not manually...
Dear friends, I have 2 callmanager servers. I have installed one as the publisher, but when when i am trying to install second one as subscriber it is not connecting with the first node (Publisher). Network connectivity is ok. My p...
Hello friends, I have an MCS 7835 IBM server .I forgot the cm administrator password . How to reset that
I have a CME(2851+VIC2-4FXO）,phone(cp-7906) calling num=7580 call PSTN by 4FXO (voice-port 0/0/3) ,An outgoing call later, prompt busy tone.phone--cme--fxo--pstn7580 0/0/3 config voice translation-rule 3rule 1 /^9/ //rule 2 /^001/ //!!voic...
Hi all,In Cisco document, they say that "Hub_None—The Hub_None location specifies unlimited audio bandwidth and unlimited video bandwidth. A device that associates with the Hub_None location allows an unlimited number of active calls to or from the d...
We are looking to upgrade our existing 7845-H2/I2s to CUCM 9. Does anyone know how to upgrade these servers to 7845-H2/I2 V02 which will support CUCM 9. The 7845-H2/I2s only support the bridged upgrade to new hardware.We found this on the hardware ...
Hello:As far as my understanding goes, hardware conferencing is not an option in CME (ver 8.x in 29xx hardware with PVDM3-64 and one E1 trunk). Is that true? If it is not, could someone post here the configuration steps specific to the hardware confe...
Dears,I have CUCM v7.1.5 and i need to know the installed SW restricted or unrestricted.How can i check this cucm?.BR,HS
Do I have to create a CAD supervisor in Agent Explorer (ICM) in order to create a password for a CUIS user? I have a manager who needs to be able to run CUIS reports, but she doesn't need CAD Supervisor. I don't know how I would go about creating/res...
Hi Support,Can you guide of how I can confirm a Video call between Cisco IP phones 9971 as I can do only voice calls, kindly advise?Sent from Cisco Technical Support iPad App
