12-07-2009 07:49 AM - edited 03-15-2019 08:42 PM
Do I need to do anything special to change my about bound CLI to BT?
I think I have made the right changes, please see my debug, how ever the call ID still shows as xxxxx300 please help
mgcp#debug isdn q931
debug isdn q931 is ON.
mgcp#ter mon
mgcp#
001878: *Dec 7 15:45:59.568 GMT: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 call ref = 0x0026
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838A
Exclusive, Channel 10
Calling Party Number i = 0x0081, '01xxxxxx300'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '07xxxxxx385'
Plan:Unknown, Type:Unknown
001879: *Dec 7 15:45:59.716 GMT: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8026
Channel ID i = 0xA9838A
Exclusive, Channel 10
001880: *Dec 7 15:46:01.160 GMT: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 c allref = 0x8026
Progress Ind i = 0x8488 - In-band info or appropriate now available
Progress Ind i = 0x8482 - Destination address is non-ISDN
001881: *Dec 7 15:46:01.388 GMT: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8 ca llref = 0x8026
001882: *Dec 7 15:46:01.392 GMT: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0026
001883: *Dec 7 15:46:04.644 GMT: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0026
Cause i = 0x8590 - Normal call clearing
001884: *Dec 7 15:46:04.776 GMT: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 ca llref = 0x8026
001885: *Dec 7 15:46:04.800 GMT: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0026
001886: *Dec 7 15:48:21.412 GMT: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0027
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838A
Exclusive, Channel 10
Calling Party Number i = 0x0081, '01xxxxxx302'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '07xxxxxx385'
Plan:Unknown, Type:Unknown
001887: *Dec 7 15:48:21.572 GMT: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8027
Channel ID i = 0xA9838A
Exclusive, Channel 10
001888: *Dec 7 15:48:22.968 GMT: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8027
Progress Ind i = 0x8488 - In-band info or appropriate now available
Progress Ind i = 0x8482 - Destination address is non-ISDN
001889: *Dec 7 15:48:23.216 GMT: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x8027
001890: *Dec 7 15:48:23.220 GMT: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0027
001891: *Dec 7 15:48:24.304 GMT: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0027
Cause i = 0x8590 - Normal call clearing
001892: *Dec 7 15:48:24.448 GMT: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x8027
001893: *Dec 7 15:48:24.480 GMT: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0027
mgcp#
mgcp#
12-07-2009 08:33 AM
For CLI to be pushed out I only needed to send 6 digits not the full number.
I'd like to thank Roy at BT for being the only person that spotted my very simple and stupid mistake.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: