Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Users might experience few discrepancies in Search results. We are working on this on our side. We apologize for the inconvenience it may have caused.
New Member

Call Back between CUCM and Siemens

Hey team,

I have a MGCP trunk working properly.

All features are working, but the call back is working in the direction Cisco for Siemens only.

For example: If I make a call from a Cisco IP phone for analog phone via MGCP and I press call back , it´s fine! But, Siemens > Cisco I have a busy ton.

thanks.

5 REPLIES
Cisco Employee

Call Back between CUCM and Siemens

What does the debugs saya about the disconnect cause???

HTH

java

if this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Call Back between CUCM and Siemens

Hey Jaime,

I will get the debug file in a few minutes...

New Member

Call Back between CUCM and Siemens

Debug log is below, but I don´t know If analog central is sending a request to call back.

3065 is analog phone.

10:40:32.845 |<:MGCPENDPOINT><:S0>|1,100,159,1.12789^*^S0/SU0/DS1-0@em01vg01

10:40:32.885 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:34.907 |MGCPpn9d::processPriSetup - viprCgpnE164=[3065], viprCdpnE164=[4800], vcrUploadNeeded=[t]|1,100,160,1.274^10.13.1.151^*

10:40:34.907 |DbMobility: can't find remdest 3065 in map|*^*^*

10:40:34.907 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:34.907 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:34.908 |!!ERROR!! -ConnectionManager- wait_AuDisconnectRequest :CI NOT FOUND IN TABLE,CI(29334280,0),discType=1,IFCreated(0,0),PID(0-0,0-0),IFHandling(0,0),MCNode(0,0)|1,100,160,1.274^10.13.1.151^*

10:40:34.908 |MatrixControl:updatePartyMediaCoordinatorNodeId: party1 videoCapable=0, party 2 videocapable=0|1,100,160,1.274^10.13.1.151^*

10:40:34.913 |<:MGCPENDPOINT><:S0>|1,100,159,1.12790^*^S0/SU0/DS1-0@em01vg01

10:40:34.989 |<:MGCPENDPOINT><:S0>|1,100,159,1.12791^*^S0/SU0/DS1-0@em01vg01

10:40:34.989 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:38.412 |<:MGCPENDPOINT><:S0>|1,100,159,1.12792^*^S0/SU0/DS1-0@em01vg01

10:40:53.388 |<:MGCPENDPOINT><:>|1,100,159,1.12793^*^*

10:41:02.722 |MGCPpn9d::processPriSetup - viprCgpnE164=[3065], viprCdpnE164=[4800], vcrUploadNeeded=[t]|1,100,160,1.276^10.13.1.151^*

10:41:02.722 |SdiStats: #Lines: 18 Free HWM: 6 Free HWM(total): 25|*^*^*

10:41:02.722 |DbMobility: can't find remdest 3065 in map|*^*^*

10:41:02.722 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:41:02.722 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:41:02.725 |!!ERROR!! -ConnectionManager- wait_AuDisconnectRequest :CI NOT FOUND IN TABLE,CI(29334282,0),discType=1,IFCreated(0,0),PID(0-0,0-0),IFHandling(0,0),MCNode(0,0)|1,100,160,1.276^10.13.1.151^*

10:41:02.725 |MatrixControl:updatePartyMediaCoordinatorNodeId: party1 videoCapable=0, party 2 videocapable=0|1,100,160,1.276^10.13.1.151^*

10:41:02.730 |<:MGCPENDPOINT><:S0>|1,100,159,1.12794^*^S0/SU0/DS1-0@em01vg01

10:41:02.848 |<:MGCPENDPOINT><:S0>|1,100,159,1.12795^*^S0/SU0/DS1-0@em01vg01

10:40:15.744 |<:MGCPENDPOINT><:S0>|1,100,159,1.12786^*^S0/SU0/DS1-0@em01vg01

10:40:15.984 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:18.840 |MGCPpn9d::processPriSetup - viprCgpnE164=[3065], viprCdpnE164=[4802], vcrUploadNeeded=[t]|1,100,160,1.271^10.13.1.151^*

10:40:18.840 |DbMobility: can't find remdest 3065 in map|*^*^*

10:40:18.840 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:18.840 |SPROC analyzeMsgtransCause MessageTransCause.ms = 0, MessageTransCause.ieid = 0, PriTsp.protocol = 29, MCStatus = 0|*^*^*

10:40:18.848 |<:MGCPENDPOINT><:S0>|1,100,159,1.12787^*^S0/SU0/DS1-0@em01vg01

10:40:18.850 |<:MGCPENDPOINT><:S0>|1,100,159,1.12788^*^S0/SU0/DS1-0@em01vg01

VIP Super Bronze

Call Back between CUCM and Siemens

Jean,

You might need to check the integration document between your siemens and cucm. I know that in some integration, call back is not fully supported

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Call Back between CUCM and Siemens

Hey,

I have checked the integration document, but I my problem is the same.

thanks.

275
Views
0
Helpful
5
Replies
CreatePlease to create content