cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
662
Views
0
Helpful
2
Replies

Call Forward voicemail issue

dkantharaj
Level 1
Level 1

I am forwarding calls that are unanswered from one ext to another which is working fine. The forwarded calls are not going to voicemail on the destination extension. Does an "Alternate Extension" else need to be configured in the SA Web portion to allow that?

1 Accepted Solution

Accepted Solutions

Rob Huffman
Hall of Fame
Hall of Fame

Hi Devaprasad,

In Unity 5.x and above you can config Unity to use the "Last Redirecting Number" on a Call Forward instead of "Originally Dialed Number"

Or like you nicely noted;

For Unity 4.x Versions;

For this configure a Voicemail profile (in CCM) for the User B and apply it to User A's DN that will allow this type of Call Forward to the desired mailbox.

Or in Unity set up Alternate Extensions so that User A is an Alternate Extension for User B etc. Sharing a Cisco Unity Voice Mail Box between Two or More IP Phones

Configure Alternate Extensions

Open the Unity System Administrator web page.

Navigate to the subscriber's profile. Select Subscribers > Find and Select a Subscriber > Enter Subscriber Information then click Find and click the Subscriber's name for the subscriber that owns the primary phone.

When the subscriber page comes up, select the Alternate Extensions option and click Add.

Enter the alternate extension number and click the Save icon.

From this good Unity doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_configuration_example09186a008015ceec.shtml#steps

Route Forwarded Calls by the First or Last Redirecting Number

Cisco Unity supports the option of routing calls based on either the first or last redirecting number when a call is forwarded to Cisco Unity.

Note the following:

This option requires Cisco Unity-CM TSP 8.1(2) or later.

This option is not supported by integrations through PIMG units.

This option can be changed through the Advanced Settings Tool (AST), which is available in Tools Depot.

http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/release/notes/501curelnotes.html#wp507371

Call Information Exchanged by the Phone System and Cisco Unity

The phone system and Cisco Unity exchange call information to manage calls and to make the integration features possible. With each call, the following call information is typically passed between the phone system and Cisco Unity:

•The extension of the called party.

•The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the phone system supports caller ID).

•The reason for the forward (the extension is busy, does not answer, or is set to forward all calls). There is also a reason code for Direct Calls.

Cisco Unified Communications Manager SCCP and SIP trunk integrations can also provide the following call information (the choice of first and last redirecting number is set in the Advanced Settings Tool, which is available in Tools Depot):

•Called number

•First redirecting number

•Last redirecting number

--------------------------------------------------------------------------------

Note Cisco Unity can use either the first redirecting number or last redirecting number, depending on the setting in the Advanced Settings Tool, which is available in Tools Depot.

http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudg060.html#wp1040786

Hope this helps!

Rob

View solution in original post

2 Replies 2

Rob Huffman
Hall of Fame
Hall of Fame

Hi Devaprasad,

In Unity 5.x and above you can config Unity to use the "Last Redirecting Number" on a Call Forward instead of "Originally Dialed Number"

Or like you nicely noted;

For Unity 4.x Versions;

For this configure a Voicemail profile (in CCM) for the User B and apply it to User A's DN that will allow this type of Call Forward to the desired mailbox.

Or in Unity set up Alternate Extensions so that User A is an Alternate Extension for User B etc. Sharing a Cisco Unity Voice Mail Box between Two or More IP Phones

Configure Alternate Extensions

Open the Unity System Administrator web page.

Navigate to the subscriber's profile. Select Subscribers > Find and Select a Subscriber > Enter Subscriber Information then click Find and click the Subscriber's name for the subscriber that owns the primary phone.

When the subscriber page comes up, select the Alternate Extensions option and click Add.

Enter the alternate extension number and click the Save icon.

From this good Unity doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_configuration_example09186a008015ceec.shtml#steps

Route Forwarded Calls by the First or Last Redirecting Number

Cisco Unity supports the option of routing calls based on either the first or last redirecting number when a call is forwarded to Cisco Unity.

Note the following:

This option requires Cisco Unity-CM TSP 8.1(2) or later.

This option is not supported by integrations through PIMG units.

This option can be changed through the Advanced Settings Tool (AST), which is available in Tools Depot.

http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/release/notes/501curelnotes.html#wp507371

Call Information Exchanged by the Phone System and Cisco Unity

The phone system and Cisco Unity exchange call information to manage calls and to make the integration features possible. With each call, the following call information is typically passed between the phone system and Cisco Unity:

•The extension of the called party.

•The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the phone system supports caller ID).

•The reason for the forward (the extension is busy, does not answer, or is set to forward all calls). There is also a reason code for Direct Calls.

Cisco Unified Communications Manager SCCP and SIP trunk integrations can also provide the following call information (the choice of first and last redirecting number is set in the Advanced Settings Tool, which is available in Tools Depot):

•Called number

•First redirecting number

•Last redirecting number

--------------------------------------------------------------------------------

Note Cisco Unity can use either the first redirecting number or last redirecting number, depending on the setting in the Advanced Settings Tool, which is available in Tools Depot.

http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudg060.html#wp1040786

Hope this helps!

Rob

Excellent, that took care of it.

Thanks You.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: