Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

call manager connect ccme

Hi everyone:

I make a experiment to simulate call manager and ccme on one pc, below is the sketch map:

ccm ----R1----R2------IP communicator 2(4803)

| (gateway) (CCME)

|

IP communicator 1 (4604)

Now IP communicator 1 can call IP communicator 2(4604---->4803) ,but 4803 cannot dial 4604, My ccm version is 5.0.1,ccme version is telephone-service 3.3 , R1 is the gateway of ccm , R2 is the ccme that ip2 register to it ,below is two router's show run , who can tell me what can I do ?

R1 show run:

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname R1

!

boot-start-marker

boot-end-marker

!

!

no aaa new-model

memory-size iomem 5

!

!

ip cef

no ip domain lookup

!

interface FastEthernet0/0

ip address 5.x.x.x.255.255.0

duplex auto

speed auto

!

interface FastEthernet1/0

ip address 172.18.1.254 255.255.255.0

duplex auto

speed auto

h323-gateway voip interface

h323-gateway voip bind srcaddr 172.18.1.254

!

ip http server

no ip http secure-server

!

ip forward-protocol nd

ip route 172.17.1.0 255.255.255.0 5.0.0.2

!

control-plane

!

sccp local FastEthernet1/0

sccp

sccp ccm 172.18.1.1 priority 1

!

dial-peer voice 2000 voip

destination-pattern 46..

session target ipv4:172.18.1.1

!

dial-peer voice 10 voip

destination-pattern 48..

session target ipv4:172.17.1.1

!

line con 0

exec-timeout 0 0

line aux 0

line vty 0 4

!

end

---------------------------------------

R2 show run:

!

version 12.4

service config

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname R2

!

boot-start-marker

boot-end-marker

!

!

no aaa new-model

memory-size iomem 5

!

!

ip cef

no ip domain lookup

interface FastEthernet0/0

ip address 5.0.0.2 255.255.255.0

duplex auto

speed auto

!

interface FastEthernet1/0

ip address 172.17.1.1 255.255.255.0

duplex auto

speed auto

!

ip http server

no ip http secure-server

!

ip forward-protocol nd

!

ip route 172.18.1.0 255.255.255.0 5.0.0.1

control-plane

!

dial-peer voice 10 voip

destination-pattern 48..

session protocol sipv2

session target ipv4:172.17.1.1

!

dial-peer voice 20 voip

destination-pattern 46..

session target ipv4:172.18.1.1

!

telephony-service

max-ephones 2

max-dn 2

ip source-address 172.17.1.1 port 2000

auto assign 1 to 2

create cnf-files version-stamp Jan 01 2002 00:00:00

max-conferences 4 gain -6

transfer-system full-consult

!

!

ephone-dn 1 dual-line

number 4803

!

!

ephone-dn 2 dual-line

number 4804

!

!

ephone 1

mac-address 000C.2900.E613

type CIPC

button 1:1

!

!

!

ephone 2

!

!

!

line con 0

exec-timeout 0 0

line aux 0

line vty 0 4

!

!

end

1 ACCEPTED SOLUTION

Accepted Solutions

Re: call manager connect ccme

first

u dont need dial-peer voice 10 voip on router 2

on both routers add the following

voice service voip

allow connection h323 to h323

then

make sure that the h323 gateway defind corectly on the CCM for example make sure is has enogh rights to call the ip comunicator 1

through partitions and CSS

if u use them

also i would suggest u to replace the following.. because u have PROBLEM with the DESTINATION IPs

replace:

dial-peer voice 20 voip

destination-pattern 46..

session target ipv4:172.18.1.1

to

dial-peer voice 20 voip

destination-pattern 46..

session target ipv4:5.0.0.1

and also:

dial-peer voice 10 voip

destination-pattern 48..

session target ipv4:5.0.0.2

i mean change the distination IPs

good luck

please if helpful Rate

3 REPLIES

Re: call manager connect ccme

first

u dont need dial-peer voice 10 voip on router 2

on both routers add the following

voice service voip

allow connection h323 to h323

then

make sure that the h323 gateway defind corectly on the CCM for example make sure is has enogh rights to call the ip comunicator 1

through partitions and CSS

if u use them

also i would suggest u to replace the following.. because u have PROBLEM with the DESTINATION IPs

replace:

dial-peer voice 20 voip

destination-pattern 46..

session target ipv4:172.18.1.1

to

dial-peer voice 20 voip

destination-pattern 46..

session target ipv4:5.0.0.1

and also:

dial-peer voice 10 voip

destination-pattern 48..

session target ipv4:5.0.0.2

i mean change the distination IPs

good luck

please if helpful Rate

New Member

Re: call manager connect ccme

haha! You are great ! you resolve my problem !thank you very much!! Now I can dial from A to B and from B to A!

Re: call manager connect ccme

u welcome!!!

but thorugh ur rating i though not solved completly:)

anyway good luck

120
Views
0
Helpful
3
Replies