Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Caller ID - Calling Name

Hello,

Environment:

Call Manager 5.1

MGCP gateways

AT&T local PRIs

Qwest LD PRIs

Phones are a mix of 7941s, 61s and 70s.

Will provide more environment info if needed.

Issue: We're able to see calling number just fine but not able to see calling name. I've checked with the AT&T telco and they've verified calling name is on our circuits. Getting confirmation from our LD provider, but they're initially saying calling name is not support on LD PRI circuits. Either way, my DID is on the AT&T circuit and all I get is number, not name. Any configuration that needs to be done for us to see it?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Caller ID - Calling Name

The exact format depends by the switch. You can see a display IE or a complicated "networking extension". The CM however understand them all.

7 REPLIES
Hall of Fame Super Gold

Re: Caller ID - Calling Name

First of all enable "debug isdn q931" and "term mon", and check what you're getting actually.

If name is not there, there is nothing that you can do to have it appear, as it's all in the hands of the telcos.

New Member

Re: Caller ID - Calling Name

Ran my debug and placed a test call and below is what I have. So basically what you're saying is if I'm not even seeing a "Calling Name" field, then the telco isn't sending it? Shouldn't I at least a "Calling Name" field that's blank??

Jan 28 17:02:37.951: ISDN Se0/1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x3948

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9838E

Exclusive, Channel 14

Calling Party Number i = 0x2181, '312735xxxx'

Plan:ISDN, Type:National

Called Party Number i = 0x80, '1312267xxxx'

Plan:Unknown, Type:Unknown

Jan 28 17:02:38.215: ISDN Se0/1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0xB948

Channel ID i = 0xA9838E

Exclusive, Channel 14

Jan 28 17:02:39.615: ISDN Se0/1/0:23 Q931: RX <- ALERTING pd = 8 callref = 0xB948

Progress Ind i = 0x8488 - In-band info or appropriate now available

Jan 28 17:02:40.191: ISDN Se0/1/0:23 Q931: RX <- CONNECT pd = 8 callref = 0xB947

Progress Ind i = 0x8482 - Destination address is non-ISDN

Jan 28 17:02:40.195: ISDN Se0/1/0:23 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x3947

Jan 28 17:02:40.647: ISDN Se0/1/0:23 Q931: RX <- CONNECT pd = 8 callref = 0xB948

Progress Ind i = 0x8482 - Destination address is non-ISDN

Jan 28 17:02:40.651: ISDN Se0/1/0:23 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x3948

Jan 28 17:02:40.667: ISDN Se0/1/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x3948

Cause i = 0x8090 - Normal call clearing

Jan 28 17:02:40.715: ISDN Se0/1/0:23 Q931: RX <- RELEASE pd = 8 callref = 0xB948

Jan 28 17:02:40.731: ISDN Se0/1/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x3948

Jan 28 17:02:40.839: ISDN Se0/0/1:23 Q931: RX <- SETUP pd = 8 callref = 0x297E

Hall of Fame Super Gold

Re: Caller ID - Calling Name

Correct, you are not given a name at all.

And is not mandatory to have a "display IE" for the name, to the contrary it would be strange to have it and be blank.

Once telco will start sending a name, it will appear on the phones.

Hope this helps, please rate post if it does!

New Member

Re: Caller ID - Calling Name

Once the telco starts sending it, will I also see "Calling Party Name" in debug isdn q931?

Hall of Fame Super Gold

Re: Caller ID - Calling Name

The exact format depends by the switch. You can see a display IE or a complicated "networking extension". The CM however understand them all.

New Member

Re: Caller ID - Calling Name

What PRI protocol are you using? NI2 is the norm that will support CID w/ Name. I don't believe DMS100 (NI1) will support it.

New Member

Re: Caller ID - Calling Name

So I opened a case with AT&T and they confirmed that Calling Name is on our circuits but isn't working as it should. They escalated it on their end and now we're able to see it. Thanks!

358
Views
0
Helpful
7
Replies