Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

caller id issue

Hello,

Jul 11 21:02:34.407: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x007D

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98386

                Exclusive, Channel 6

        Facility i = 0x91A12702026EE902010F301E0201010A0101A116A014A1120A0101120D39313132343431333238303233

        Calling Party Number i = 0x1183, '9101206712000'

                Plan:ISDN, Type:International

        Called Party Number i = 0x81, '2023'

                Plan:ISDN, Type:Unknown

Jul 11 21:02:34.415: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x807D

        Channel ID i = 0xA98386

                Exclusive, Channel 6

Jul 11 21:02:34.415: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8  callref = 0x807D

        Facility i = 0x9FAA06800100820100A1080201010201018400

        Progress Ind i = 0x8088 - In-band info or appropriate now available

Jul 11 21:02:38.195: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x007D

        Cause i = 0x8090 - Normal call clearing

Jul 11 21:02:38.215: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x807D

Jul 11 21:02:38.279: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x007D

        Cause i = 0x8090 - Normal call clearing

Jul 11 21:02:38.783: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x007E

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98387

                Exclusive, Channel 7

        Facility i = 0x91A11902026FCA02010F30100201010A0103A108A006800435383030

        Calling Party Number i = 0x0083, '7459'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '2112'

                Plan:Unknown, Type:Unknown

        High Layer Compat i = 0x9181

Jul 11 21:02:38.787: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x807E

        Cause i = 0x8081 - Unallocated/unassigned number Calling Party Number i = 0x1183, '9101206712000'

The caller id shown "9101206712000" is incorrect. it should be either "911206712000" or "01206712000". how can i change it?

Kindly help.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

caller id issue

This is what the telco is sending you, you can have them change it, or if you want you can add a translation rule to the GW to strip  or prefix digits.

HTH,

Chris

1 REPLY
Hall of Fame Super Silver

caller id issue

This is what the telco is sending you, you can have them change it, or if you want you can add a translation rule to the GW to strip  or prefix digits.

HTH,

Chris

133
Views
0
Helpful
1
Replies
CreatePlease to create content