Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cannot get into CUE CLI

I am looking to do an upgrade of our version of CUE on a 2821 NME.  The current CUE (3.0.4) is currently working fine, however I want to update the version of CME running on my router.  The problem is I cannot get into the service-module session. When I try it is saying connection refused by host... I have tried to clear the line via the service-module integ-service-engine 1/0 session clear and by clearing the tty line that shows in the service-module integ-service-engine 1/0 status (via clear line tty 66).  I have tried shutting down the module and restarting it with no avail.  I am at a loss as to what to do to get into the cli for the CUE.  Any ideas?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Cannot get into CUE CLI

Under line 66

no exec

transport input all

9 REPLIES
Bronze

Re: Cannot get into CUE CLI

Do you have a copy of the configuration? Can you web to the CUE?

cheers

Mark

New Member

Re: Cannot get into CUE CLI

The web gui is working fantastically. 

...

!

interface Loopback0

ip address 172.16.5.2 255.255.255.252

!
...
!
interface Integrated-Service-Engine1/0
ip unnumbered Loopback0
service-module ip address 172.16.5.1 255.255.255.252
service-module ip default-gateway 172.16.5.2
no keepalive
!
...
!
ip route 172.16.5.1 255.255.255.255 Integrated-Service-Engine1/0
!
...
!
dial-peer voice 1000 voip
translation-profile outgoing PSTN-CallForwarding
destination-pattern 600
session protocol sipv2
session target ipv4:172.16.5.1
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 1010 voip
description Auto Attendant
translation-profile outgoing PSTN-CallForwarding
destination-pattern 650
session protocol sipv2
session target ipv4:172.16.5.1
dtmf-relay sip-notify
codec g711ulaw
!
...
I would not have noticed any problems if it was not for the upgrade I am attempting to do.

Bronze

Re: Cannot get into CUE CLI

Can't seem to see a problem, what command are you using to access the cli?

Mark

New Member

Re: Cannot get into CUE CLI

#service-module integrated-Service-Engine 1/0 session

Trying 172.16.5.2, 2066 ...

% Connection refused by remote host

#service-module integrated-Service-Engine 1/0 session clear
[confirm]
[OK]
#service-module integrated-Service-Engine 1/0 session
Trying 172.16.5.2, 2066 ...
% Connection refused by remote host

Bronze

Re: Cannot get into CUE CLI

very strange , can't see what the issue is.The fact that you can use the CUE and web to it must mean that routing is fine.i can only assume that it maybe a bug in the IOS.what version are you running.I have checked the unity express for bugs regarding this but there is nothing obvious

New Member

Re: Cannot get into CUE CLI

IOS version 12.4(11)XW9

CUE version 3.0.4

Hall of Fame Super Gold

Re: Cannot get into CUE CLI

Under line 66

no exec

transport input all

New Member

Re: Cannot get into CUE CLI

What authentication are you using for the module?

Hall of Fame Super Gold

Re: Cannot get into CUE CLI

What authentication are you using for the module?

Note: Problem has been solved and checkmarked as such .

4464
Views
5
Helpful
9
Replies