Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Users might experience few discrepancies in Search results. We are working on this on our side. We apologize for the inconvenience it may have caused.

Castelle Fax Integration with E1 PRI on ISR

Hi,

I am having trouble integrating Castelle Enterprise Fax Press. I have done the required config on the Router as below:

controller E1 0/3/0

pri-group timeslots 1-16

description <<26_CHANNELS_CONNECTED_TO_FAX_SERVER>>

!

interface Serial0/3/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn protocol-emulate network

isdn incoming-voice voice

isdn outgoing ie redirecting-number

no cdp enable

!

dial-peer voice 3960 pots

description <<DIAL_PEER_TO_CASTELLE_FAX>>

destination-pattern 39[678].

fax rate fax

port 0/3/0:15

!

The Fax is delivered to the Fax Server, but the Castelle guys say that they are not receiving the DNIS.

From the Service Provider, I am receiving 4 Digits and I am sending 4 dgitis to the Dial-Peer 3960.

Is there anything else that I have to send inorder to get this right?

*Nov 20 19:53:32.649: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x2C15

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8483 - Origination address is non-ISDN

Calling Party Number i = 0x2183, '026412160'

Plan:ISDN, Type:National

Called Party Number i = 0x81, '3960'

Plan:ISDN, Type:Unknown

*Nov 20 19:53:32.701: ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x

AC15

Channel ID i = 0xA98381

Exclusive, Channel 1

*Nov 20 19:53:32.797: ISDN Se0/3/0:15 Q931: RX <- ALERTING pd = 8 callref = 0xA

C15

*Nov 20 19:53:32.797: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xE

97F

*Nov 20 19:53:32.821: ISDN Se0/3/0:15 Q931: RX <- CONNECT pd = 8 callref = 0xAC

15

*Nov 20 19:53:32.825: %ISDN-6-CONNECT: Interface Serial0/3/0:0 is now connected

to 3960 N/A

*Nov 20 19:53:32.825: ISDN Se0/3/0:15 Q931: TX -> CONNECT_ACK pd = 8 callref =

0x2C15

*Nov 20 19:53:32.829: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xE9

7F

*Nov 20 19:53:33.341: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref =

0x697F

*Nov 20 19:53:33.341: ISDN Se0/0/0:15 **ERROR**: call_progress: DEV_CONNECTED VO

ICE ERROR: Bearer capability not available(0x3A): b channel 12 call id 0x3054

*Nov 20 19:53:33.341: %ISDN-6-CONNECT: Interface Serial0/0/0:12 is now connected

to 026412160 N/A

*Nov 20 19:53:49.885: %C3800_ENVM-3-MFAIL_OFF: There is more than one failure wi

th the Power System 2 or this Power System has been turned off.

*Nov 20 19:54:09.885: %C3800_ENVM-3-MFAIL_OFF: There is more than one failure wi

th the Power System 2 or this Power System has been turned off.

*Nov 20 19:54:13.761: ISDN Se0/3/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0

xAC15

Cause i = 0x8090 - Normal call clearing

*Nov 20 19:54:13.765: %ISDN-6-DISCONNECT: Interface Serial0/3/0:0 disconnected

from 3960 , call lasted 40 seconds

*Nov 20 19:54:13.765: ISDN Se0/3/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x2C

15

*Nov 20 19:54:13.765: %ISDN-6-DISCONNECT: Interface Serial0/0/0:12 disconnected

from 026412160 , call lasted 40 seconds

*Nov 20 19:54:13.765: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0

xE97F

Cause i = 0x8090 - Normal call clearing

*Nov 20 19:54:13.773: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref =

0xAC15

*Nov 20 19:54:13.941: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x69

7F

*Nov 20 19:54:13.941: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref =

0xE97F

Thanks & Regards,

Sriharshaa Prabhakar

Senior Network Engineer

Network Services Division

Emirates Computers

P.O.Box 7222, Abu Dhabi, U.A.E.

Phone: +971 2 673 2500

Mobile: +971 50 521 29 56

E-mail: sriharshaa.p@ecead.ae

Web: www.emiratescomputers.ae

3 REPLIES
Hall of Fame Super Gold

Re: Castelle Fax Integration with E1 PRI on ISR

Hi,

the device disconnecting the call after 40 seconds. What is the problem ?

Re: Castelle Fax Integration with E1 PRI on ISR

Hi,

That call was disconnected by me, it is not disconnecting the call in 40 Seconds, I would like to know is there any way to hardcode DNIS to be sent by Router to the Fax Server?

Regards,

Sriharshaa Prabhakar

New Member

Re: Castelle Fax Integration with E1 PRI on ISR

Sriharshaa,

Did you get this resolved? I am looking at the Castelle Enteprise Fax appliance and would like any input when interfacing with Cisco Call Manager

224
Views
0
Helpful
3
Replies
CreatePlease to create content