Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cbarge in CME "Failed to Cbarge In"

Hi all

I would much appreciate if someone can help me to overcome the following issue. I have configured a Cbarge feature in CME and due to the hardware conference issue I am not able to test the feature. It is giving me the error message as “ Failed to Barge in”

I know it is a hardware conference issue, however I don’t find any mistake in the config and the hardware conference is associated successfully with CME.

Please see the detail and give me a direction as where I am making the mistake…… it is killing my time

Thanks

PVDM2 - Details

=====

Slot0:

PVDM Slot 1:
        48-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
        Hardware Revision        : 4.0
        Part Number              : 73-8540-05
        Board Revision           : A0
        Deviation Number         : 0
        Fab Version              : 04
        PCB Serial Number        :

        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Processor type           : 00
        Product (FRU) Number     : PVDM2-48
        Version Identifier       : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 03 ED 41 04 00 82 49 21 5C 05 42 41 30
          0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 30 34 34
          0x20: 33 57 31 43 03 00 81 00 00 00 00 04 00 09 00 CB
          0x30: 88 50 56 44 4D 32 2D 34 38 89 56 30 31 20 D9 02
          0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

=================Config-=================

voice-card 0
dspfarm
dsp services dspfarm
!
sccp local FastEthernet0/0.105
sccp ccm 142.105.66.254 identifier 1 priority 1 version 7.0
sccp
!
sccp ccm group 1
bind interface FastEthernet0/0.105
associate ccm 1 priority 1
associate profile 2 register myconf
associate profile 1 register mytrans
keepalive retries 5
keepalive timeout 5
!
dspfarm profile 1 transcode 
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 3
associate application SCCP
!
dspfarm profile 2 conference 
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP


telephony-service
sdspfarm units 2
sdspfarm transcode sessions 3
sdspfarm tag 1 mytrans
sdspfarm tag 2 myconf
conference hardware

=================================

abc#sh dsp
abc#sh dspfarm all
Dspfarm Profile Configuration

Profile ID = 1, Service = TRANSCODING, Resource ID = 1 
Profile Description : 
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP   Status : ASSOCIATED
Resource Provider : FLEX_DSPRM   Status : UP
Number of Resource Configured : 3
Number of Resource Available : 3
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30
Codec : g711alaw, Maximum Packetization Period : 30
Codec : g729ar8, Maximum Packetization Period : 60
Codec : g729abr8, Maximum Packetization Period : 60
Dspfarm Profile Configuration

Profile ID = 2, Service = CONFERENCING, Resource ID = 2 
Profile Description : 
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP   Status : ASSOCIATED
Resource Provider : FLEX_DSPRM   Status : UP
Number of Resource Configured : 2
Number of Resource Available : 2
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required


SLOT DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0    5   23.8.1   UP     N/A  FREE  xcode  1      -         -         -       
0    5   23.8.1   UP     N/A  FREE  xcode  1      -         -         -       
0    5   23.8.1   UP     N/A  FREE  xcode  1      -         -         -       
0    7   23.8.1   UP     N/A  FREE  conf   2      -         -         -       
0    7   23.8.1   UP     N/A  FREE  conf   2      -         -         -      

Total number of DSPFARM DSP channel(s) 5

=================== Debug during Cbarge====================

debug ephone hw-conference

Jun 26 03:41:27.694: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:27.694: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:27.706: Check associated hwconf with callid 15

Jun 26 03:41:27.710: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:27.710: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:30.602: Check associated hwconf with callid 15

Jun 26 03:41:30.990: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0

Jun 26 03:41:30.990: SkinnyHwconfBridgeMedia:Call not in conference

Jun 26 03:41:31.587: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:31.587: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:33.183: SkinnyCBargeButtonPress: New adhoc conf barge

Jun 26 03:41:33.183: skinny_hwcfb_get_adhoc_number:

Jun 26 03:41:33.183: SkinnyCBargeButtonPress: New adhoc conf barge: setup failed!

Jun 26 03:41:44.523: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0

Jun 26 03:41:44.559: SkinnyHwconfConfSKButtonSet:for dn 4 chan 1 set=0 conf_sk=0

===================When I try to conference =========================

un 26 03:45:08.777: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:08.785: Check associated hwconf with callid 17
Jun 26 03:45:08.789: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:09.869: Check associated hwconf with callid 17
Jun 26 03:45:10.253: SkinnyHwconfBridgeMedia:dn = 2, chan 1, phone = 1 stream 0
Jun 26 03:45:10.253: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:10.589: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:11.445: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:15.857: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:15.881: SkinnyHideAdhocConfNumber for dn=3 chan=1 streamID=0
Jun 26 03:45:16.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:16.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:17.841: SkinnyHwconfBridgeMedia:dn = 3, chan 1, phone = 0 stream 0
Jun 26 03:45:17.841: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:17.889: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0
Jun 26 03:45:17.889: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:18.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:18.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: phone=1 (dn=2 chan=1 state=9) (conf_dn=4 conf_chan=1 state=4)
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: New adhoc conference
Jun 26 03:45:22.017: skinny_hwcfb_get_adhoc_number:
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: Adhoc new conference setup failed!
Jun 26 03:45:23.817: SkinnyHideAdhocConfNumber for dn=4 chan=2 streamID=0
Jun 26 03:45:28.165: SkinnyHideAdhocConfNumber for dn=4 chan=2 streamID=0
Jun 26 03:45:28.193: SkinnyHwconfConfSKButtonSet:for dn 4 chan 2 set=0 conf_sk=0
Jun 26 03:45:30.461: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:30.481: SkinnyHwconfConfSKButtonSet:for dn 2 chan 1 set=0 conf_sk=0
Jun 26 03:45:34.161: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:34.161: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:34.321: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0
Jun 26 03:45:34.321: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:35.277: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:35.313: SkinnyHideAdhocConfNumber for dn=3 chan=1 streamID=0
Jun 26 03:45:35.317: SkinnyHwconfConfSKButtonSet:for dn 4 chan 1 set=0 conf_sk=0
Jun 26 03:45:35.317: SkinnyHwconfConfSKButtonSet:for dn 3 chan 1 set=0 conf_sk=0

================================================================

As trouble shooting step, I trying to add the " conference ad-hoc under the ephone-dn ( otc-lie), it is giving me error)

Abc(config-ephone-dn)#conference ad-hoc
DN 4 is tied to ephone 1 button 3
Remove dn 4 from the ephone button config

If i remove the button, I am not able to share the line with 2 phone for Cbarge

thanks for your help and time

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Cbarge in CME "Failed to Cbarge In"

Hi, you are not configuring the conference DN properly. Create the DN like below:

!

ephone-dn x octo-line

number A100

conference ad-hoc

!

ephone-dn y octo-line

number A101

conference ad-hoc

!

Never think to use any existing DN (which is used on any phone) as conference DN. Also 'number A100/A101' means it's not dialable by any user mistakenly, only system can call the DN.

HTH.

Please rate helpful posts!

1 REPLY

Re: Cbarge in CME "Failed to Cbarge In"

Hi, you are not configuring the conference DN properly. Create the DN like below:

!

ephone-dn x octo-line

number A100

conference ad-hoc

!

ephone-dn y octo-line

number A101

conference ad-hoc

!

Never think to use any existing DN (which is used on any phone) as conference DN. Also 'number A100/A101' means it's not dialable by any user mistakenly, only system can call the DN.

HTH.

Please rate helpful posts!

1146
Views
0
Helpful
1
Replies
CreatePlease login to create content