cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1227
Views
0
Helpful
9
Replies

CCIE Voice lab question

Curtis Fuentes
Level 1
Level 1

                   Hi,

        I am building my lab for the CCIE voice exam. I am currently working on my frame relay PSTN. I am able to get my PSTN ports to come up, but I am having issues with my framerelay.I thin is a cable issue because the ports are down/ down. I was wondering what type of cables are need for the frame relay ports. I am following the IPexpert and using vwics.

Thank you

1 Accepted Solution

Accepted Solutions

Hi Curtis.

Now the problem is Frame Relay related I guess..

Try to set clock on the dce side and see if it works

Bye

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

View solution in original post

9 Replies 9

Hi.
You should use a DTE/DCE cable to achieve what you are trying.


HTH

Regards

Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"

Hi,

       Keep in mind that I am using Vwic cards not WIC cards.

Thank you

Ops..

Sorry Curtis.

In my case  worked an RJ45 with the following pinout:

1-2-3-4-5-6-7-8 ---> 4-5-3-1-2-6-7-8

You can try it and hope this helps.

If you can, please post your config.

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

Hi.

VWIC can also be configured as WAN interface  loosing Voice capability.

http://www.cisco.com/en/US/prod/collateral/routers/ps274/product_data_sheet09186a0080091b9c_ps259_Products_Data_Sheet.html

Curtin, you can  try to decrease speed on your channel-group

HTH

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

Thanks I will try it tonight when I get off work. Below is the config offered by IPexperts.

Branch office  

controller T1 0/0/0

framing esf

linecode b8zs

pri-group timeslots 1-3,24 service mgcp

!

controller T1 0/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

interface Serial0/0/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

interface Serial0/0/1:0

no ip address

encapsulation frame-relay IETF

no fair-queue

frame-relay lmi-type ansi

!

PSTN

controller T1 0/0/0
framing esf
clock source internal
linecode b8zs
channel-group 0 timeslots 1-24

controller T1 0/3/1
framing esf
clock source internal
linecode b8zs
pri-group timeslots 1-3,23-24
description ** T1 VOICE CONNECTION TO BR1-RTR ** description ** SERIAL DATA CONNECTION TO BR1-RTR **

interface Serial0/0/0:0
description ** T1 DATA CONNECTION TO BR1-RTR **
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
frame-relay route 101 interface Serial0/1/0:0 201

interface Serial0/3/1:23
description ** T1 PRI D-CHANNEL TO BR1-RTR **
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable

Hi Carlo,

    I   used the pinout you gave me the ligh on the cards are green. The issue that I have now isthe interface is up but the protocol is down.

Hi Curtis.

Now the problem is Frame Relay related I guess..

Try to set clock on the dce side and see if it works

Bye

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

Carlo you are the man it is working now..

Thank you

Glad to help.
Regards.
Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: